Homework Answers
Add Answer to:
1. A machined entrance cone venturi to be installed into a 15-cm (inlet diameter) pipe, which...
A venturi meter with a diameter of 30 cm at the entrance and 15 cm at...
A venturi meter with a diameter of 30 cm at the entrance and 15
cm at the throat, is connected to a vertical pipe of diameter 30cm
carrying oil of specific gravity 0.9. The difference in elevation
of the throat section and the entrance of the venturi meter is 30
cm. The mercury manometer shows a gauge deflection of x =
1000mm.
Determine
1) the discharge of oil; and
2) the pressure difference between the entrance section and
throat section....
A venturi meter was installed in a pipe to measure the flow of the water inside....
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
A vertical venturi-meter is connected to a vertical pipe which carries water as shown in the...
A vertical venturi-meter is connected to a vertical pipe which carries water as shown in the figure. the diameters at the entrance and throat are 150 mm and 75 mm, respectively. The the mercury (specific gravity +13.6). U-tube mercury manometer connected to the entrance and throat of the meter . the height difference between the throat and entrance is 150mm.If the actual rate is 40 liters/s and the coefficient of discharge is 0.96, calculate (a) the pressure difference between entrance and...
Q8 A horizontal pipe 50 mm diameter is fitted with a venturi tube, which has a...
Q8 A horizontal pipe 50 mm diameter is fitted with a venturi tube, which has a throat diameter of 40 mm. The pipe carries water at a pressure of 30 kPa gauge and velocity 3 m/s upstream of the throat. Determine: a. The mass flow rate; b. The velocity at the throat C. The pressure at the throat ignoring head losses: d. The pressure at the throat if a head loss equal to 5% of the total head occurs as...
QUESTION 7 20 points Save Answer A rough cast venturi tube "Herschel type" flow detector is...
QUESTION 7 20 points Save Answer A rough cast venturi tube "Herschel type" flow detector is used in a pipe carrying a fluid, and measures a differential pressure described in the table below. Determine the flow rate in gallons per minute (gpm). Water at 100 OF Schedule 40 Steel Fluid Inlet pipe Inlet pipe nominal diameter (inches) Throat diameter (inches) Differential pressure inlet-to-throat (psid) 6 3 12
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe...
Please solve a,b,c,d,e,f
1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
The system shown in the diagram consists of 1200m of cast-iron pipe with an internal diameter...
The system shown in the diagram consists of 1200m of cast-iron pipe with an internal diameter of 5cm (roughness of 0.00015 ft), two 45o and four 90o long radius elbows, a fully open bevel seat globe valve, and a sharp exit into a reservoir. If the elevation difference between the inlet and level in the reservoir is 10m, what gauge pressure is required at point 1 to deliver 0.005m^3/s of water at 20oC into the reservoir (use density of 998.2...
fluid Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at...
fluid
Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at 40° to the horizontal to measure the flow rate of petrol having a specific gravity of 0.8. The ratio of areas of main pipe and throat is 5 and the throat is at 1 m from the inlet along its length. The difference in manometer head is 40 mm of mercury. Assuming the coefficient of discharge as 0.96. Calculate the discharge through the venture...
CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200...
CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200 mm when the difference of pressure head between the ends of the pipe 500 m apart is 4 m of water. Take the value off= 0.009 in the formula hl= a) 19.5e/s b)2.0es e)03 m's d) 29.3 e/s 2. A scale 1:50 scale model of ship is towed through sea water at a speed of 1 ms. A force of 2 N is required...
A venturi meter with a diameter of 30 cm at the entrance and 15
cm at the throat, is connected to a vertical pipe of diameter 30cm
carrying oil of specific gravity 0.9. The difference in elevation
of the throat section and the entrance of the venturi meter is 30
cm. The mercury manometer shows a gauge deflection of x =
1000mm.
Determine
1) the discharge of oil; and
2) the pressure difference between the entrance section and
throat section....
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
Q8 A horizontal pipe 50 mm diameter is fitted with a venturi tube, which has a throat diameter of 40 mm. The pipe carries water at a pressure of 30 kPa gauge and velocity 3 m/s upstream of the throat. Determine: a. The mass flow rate; b. The velocity at the throat C. The pressure at the throat ignoring head losses: d. The pressure at the throat if a head loss equal to 5% of the total head occurs as...
QUESTION 7 20 points Save Answer A rough cast venturi tube "Herschel type" flow detector is used in a pipe carrying a fluid, and measures a differential pressure described in the table below. Determine the flow rate in gallons per minute (gpm). Water at 100 OF Schedule 40 Steel Fluid Inlet pipe Inlet pipe nominal diameter (inches) Throat diameter (inches) Differential pressure inlet-to-throat (psid) 6 3 12
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...
Please solve a,b,c,d,e,f
1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
fluid
Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at 40° to the horizontal to measure the flow rate of petrol having a specific gravity of 0.8. The ratio of areas of main pipe and throat is 5 and the throat is at 1 m from the inlet along its length. The difference in manometer head is 40 mm of mercury. Assuming the coefficient of discharge as 0.96. Calculate the discharge through the venture...
CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200 mm when the difference of pressure head between the ends of the pipe 500 m apart is 4 m of water. Take the value off= 0.009 in the formula hl= a) 19.5e/s b)2.0es e)03 m's d) 29.3 e/s 2. A scale 1:50 scale model of ship is towed through sea water at a speed of 1 ms. A force of 2 N is required...
Most questions answered within 3 hours.
-
HELP WITH SAS
Run the following DATA step to create a SAS data set called
ABC_CORP....
asked 5 minutes ago -
A researcher wishes to study the cumulative effects of several
combinations of HIV drugs. There are...
asked 25 minutes ago -
How
to make a simple game of whack a mole in pygame
asked 8 minutes ago -
Write a c/c++ program to read a list of students from a file and
create a...
asked 17 minutes ago -
Identify two different methods for collecting data in
qualitative research. What are the benefits and challenges...
asked 18 minutes ago -
I am suppose to have my array before the main class but I am
getting the...
asked 20 minutes ago -
Your task is to design the page table for the 32bit Pentium
microprocessor. Answer the following...
asked 26 minutes ago -
The Paradise Shoes Company has estimated its weekly TVC function
from data collected over the past...
asked 24 minutes ago -
Although Epicurus advocates pursuing pleasure for the
good life, discuss a few reasons why he does...
asked 42 minutes ago -
Problem 1: Present entries to record the selected transactions
described below:
(a)
Issued $2,790,000 of 5-year,...
asked 48 minutes ago -
Using technology to support HR activities increases:
a.
the efficiency of the administrative HR functions.
b....
asked 49 minutes ago -
1. List the features used to classify leaf
types.
2. List some characteristics that are shared...
asked 54 minutes ago