Challenge Problem: A thin rod of mass M-209 kg and length L-0.782 m is suspended from...
1. A thin rod of mass M and length d hangs vertically from a frictionless pivot attached to one end. A piece of clay of mass m moving horizontally at a speed v hits the rod a distance x from the pivot and sticks to it. Discussion Questions: (In the first 5-10 min a random group will be selected to explain.) • What “type” of collision is happening? What is and is not conserved? • Consider the analogous linear momentum...
Q21 (15 points): A uniform rod of mass m 1.5 kg and length d- 2.0 m is supported by a pivot point P at its top and is free to rotate iın the vertical plane. A block of mass m2 0.8 kg is attached to the other end of the rod. The rod-block system is initially at rest, and a 1g bullet is fired horizontally into the rod through a point x 08 d below the pivot P Assume that...
The figure shows a thin rod, of length L = 2.10 m and negligible mass, that can pivot about one end to rotate in a vertical circle. A heavy ball of mass m = 9.20 kg is attached to the other end. The rod is pulled aside to angle θ0 = 22.0° and released with initial velocity = 0. As the ball descends to its lowest point, (a) how much work does the gravitational force do on it and (b)...
The figure shows a thin rod, of length L = 1.6 m and negligible mass, that can pivot about one end to rotate in a vertical circle. A heavy ball of mass m = 9.1 kg is attached to the other end. The rod is pulled aside to angle θ0 = 6.4° and released with initial velocity v Overscript right-arrow EndScripts Subscript 0 = 0. As the ball descends to its lowest point, (a) how much work does the gravitational...
(10%) Problem 8: A rod of mass M and length L can rotate about a hinge at its left end and is initially at rest. A putty ball of mass m, moving with speed V strikes the rod at angle from the normal and sticks to the rod after the collision Otheexpertta.com 50% Part (a) What is the total moment of inertia. I, with respect to the hinge, of the rod-ball-system after the collision? Correct! * 50% Part(b) What is...
A uniform thin rod of length 0.500 m and mass 4.00 kg is attached to a pivot at one end. The other end of the rod is attached to a uniform sphere with a mass of 2.00 kg and a radius of 0.100 m. The rod and sphere initially hang vertically. A bullet with a mass of 5.00 g is fired horizontally at a speed of 200 m/s into the center of the sphere. The bullet embeds itself in the...
Two 3.00 kg balls are attached to the ends of a thin rod of negligible mass, 50.0 cm long. The rod is free to rotate in a vertical plane without friction about a horizontal axis through its center. While the rod is horizontal (Fig. 12-46), a 65.0 g putty wad drops onto one of the balls with a speed of 3.00 m/s and sticks to it.(a) What is the angular speed of the system just after the putty wad hits?(b)...
A thin rod of mass m and length l rests on a frictionless table and is struck at a point l/4 from its center of mass by a clay ball of mass m moving at speed v. The ball sticks to the rod. If the rod is free to pivot about a frictionless pin at its center, find the angular velocity of the rod after the collision. Also find the velocity of the point at the top of the rod...
Q20 (15 points): A bullet of mass m X102 kg is moving with a speed of 100 m/s when it collides with a rod of mass mR 5 kg and length L m (shown in the figure). The rod is initially at rest, in a vertical position, and pivots about an axis going through its center of mass. The bullet imbeds itself in the rod at a distance L/4 from the pivot point. As a result, the bullet-rod system starts...
A thin, uniform bar of length D = 1.00 m and mass M = 0.74 kg pivoted at the top. The rod, which is initially at rest, is struck by a particle whose mass is m = 0.30 kg at a point x = 0.80d below the pivot. Assume that the particle sticks to the rod. If the maximum angle between the rod and the vertical following the collision is 60°, find the speed of the particle before impact.