A thick walled pressure cylinder has an outer diameter 209 mm, external pressure 4 MPa, and maximum allowable shear stress 29 MPa. What is the wall thickness of the pressure cylinder?
Hints: Find internal radius by using internal pressure 0 and tau_max = (sigma_t - sigma_r)/2. then t=r_0 - r_i
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
please make your answers clear and organized . Problem 8.5-3 A cylindrical pressure vessel having radius r-300 mm and wall thickness t 15 mm is subjected to internal pressure p 2.5 MPa. In addition, a torque T120 kN-m acts at each end of the cylinder (see figure) (a) Determine the maximum tensile stress ?mix and the maximum in-plane shear stress Tmax in the wall of the cylinder torque T? 30 MPa and 76 MPa, respectively, what is the minimum required...
with steps please Question4 A thick-walled cylinder of mild steel with internal diameter of 80 mm and external diameter of 120 mm is loaded by internal pressure. The yield strength of the material is 300 MPa. a. Find the internal pressure required to initiate yielding in the cylinder using Lame's formulation. Sketch the stress distribution giving significant stress values. b. Find the plastic limit pressure at which the cylinder is fully plastic using non-linear formulation. Sketch the stress distribution giving...
A thick-walled steel cylinder with internal diameter = 16 mm and external diameter = 24 mm is subjected to a gradually increasing internal pressure P. I. Using accurate formulation, determine the value of P and sketch the distribution of radial, tangential and maximum shear stresses when: a. The material of the cylinder first commences to yield. b. Yielding progressed to mid-depth of the cylinder wall (at D= 20 mm ). c. The material of the cylinder suffers complete collapse (fully...
2. (15 points) A pressure cylinder with an outer diameter do = 200 mm and wall thickness t = 6 min carries an internal pressure of 4 MPa. Determine the maximum tangential, radial, longitudinal stresses in the cylinder. What is the maximum shear stress? [Ans: ơttinax-64.73 MPa, ơrr, max-一4.00 MPa, dzina.-30.36 MPa, and Tmax-34.37 MPa.
UESTION # 2: (20 Marks) The thick cylinder shown in Fig. Q2(a) is made of high strength steel with an internal diameter of 200 mm and an external diameter of 300 mm. It is subjected to an internal pressure P 60 MPa The cylinder is assumed to have closed ends, as depicted in Fig. Q2(b) (a) Determine the stress state acting on the element abcd located on the outer surface of the cylinder as a result of Pi; see Fig....
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yield stress of 240 MPa. +F 200 mm Fig. Q5 (a) If a tensile axial force of 1MN is applied to the end plate, show that the maximum internal pressure that can be applied before the cylinder yields according to the Tresca criterion is 16.2...
Problem 1: (a)A thick-walled cylinder, made from a homogeneous and isotropic elastic material, has an inner radius a and outer radius b. The cylinder is subjected to an internal pressure pi, and is under plane stress conditions. In this case the displacement field is of interest is given by and the stress field of interest is given by C2 C2 where, with (E and v) denoting the Young's modulus and the Poisson's Ratio. EA EB Show that b2 b2 (b/a)2-1)...
with steps please!!! Question3 Design a thick-walled metallic cylinder of a 200 mm internal diameter for an internal pressure of 30 MPa such as to provide a factor of safety of 3.0 against any yielding in the cylinder and a factor of safety of 4.0 against ultimate collapse. The yield stress of the material is 480 MPa Use both linear and non-linear stress distribution methods of calculation. Compare and discuss the results. Question3 Design a thick-walled metallic cylinder of a...
8.5-8 A pressurized cylindrical tank with flat ends is loaded by torques Tand tensile forces P (see figure). The tank has a radius of r = 125 mm and wall thick- ness t 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 850 N·m. (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 160 MPa? (b) If forces P 400 kN,...
Problem 1. A I meter inner diameter steel pressure tank with 8 mm wall thickness is subject to a internal pressure of 1.5 MPa and due to the piping weight a torsion of 10 Nm is acting as shown in the figure. The length of the cylinder is 3 meters. Determine: The state of stress in the cylinder wall The state of stress if the normal Cartesian system is rotate 250 The principal stress and the principal angle. The maximum...