Problem 7: Consider a slab milling operation. Milling machine holds the tool horizontally. The length and...
Problem 7:
Consider a slab milling operation. Milling machine holds the tool horizontally.
The length and the width of the part are 850 mm and 30 mm respectively.
Tool diameter is 40 mm The number of the installed inserts was 10.
Feed per tooth is 0.3 mm/tooth. Cutting speed is 1 m/sec.
Depth of cut is 2 mm. Specific energy is 2 W.s/mm3
a) Find the machining time?
b) Calculate the MRR
c) What would be the required power?
d) Find the necessary torque?
Homework Answers
Add Answer to:
Problem 7:
Consider a slab milling operation. Milling
machine holds the tool horizontally.
The length and...
A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiec...
A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate: ‧ the material-removal rate; ‧ the power and torque required for this...
A slab-milling operation is being carried out on a block on a 200 mm-long, 150 mm-wide...
A slab-milling operation is being carried out on a block on a 200 mm-long, 150 mm-wide annealed mild steel block at a feed f= 0.20 mm/tooth and depth of cut d= 2.5 mm. The cutter is D= 45 mm in diameter, has 20 straight teeth, rotates at N=110 rpm and by the definition, is wider than the block to be machined. Calculate ; I.material-removal, II.estimate the power and torque required for this operation, III.calculate the cutting time
2.(USCS units) A face milling operation is performed on the top surface of a steel block...
2.(USCS units) A face milling operation is performed on the top surface of a steel block that is 12.0 in long by 3.0 in wide by 2.5 in thick. The milling cutter follows a path that is centered over the width of the block. It has five teeth and a 3.0 in diameter. Cutting speed-250 ft/min, feed- 0.006 in/tooth, and depth of cut -0.150 in. Determine (a) machining time and (b) maximum removal rate during the cut. (c) If an...
A face milling operation removes 4.0 mm from the top surface of a rectangular piece of...
A face milling operation removes 4.0 mm from the top surface of a rectangular piece of aluminum that is 200 mm long by 60 mm wide by 75 mm thick. The cutter follows a path that is centered over the workpiece. It has four teeth and is 100 mm in diameter. Cutting speed = 2.5 m/s, and chip load = 0.27 mm/tooth. Determine (a) maximum metal removal rate during cutting in mm3/seconds (b) machining time in seconds. Cutter position at...
1. A face milling operation is performed on the top surface of a steel rectangular workpiece...
1. A face milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in long by 2.5 in wide. The milling cutter follows a path that is centered over the workpiece. It has five teeth and a 3.0 in diameter. Cutting speed = 250 ft/min, feed = 0.006 in/tooth, and depth of cut = 0.150 in. Determine (a) the actual cutting time to make one pass across the surface and (b) the maximum metal removal rate...
answer a) is 1.35 and b) 7.16 i want the answer for c Problem #4 A...
answer a) is 1.35 and b) 7.16 i want the answer for c Problem #4 A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in fong by 2.5 in wide. The helical milling cutter, which has a 3.0 in diameter and ten teeth, is set up to overhang the width of the part on both sides. Cutting speed is 125 ft/min, feed is 0.006 in/tooth, and depth of cut - 0.300 in.? Determine...
Industrial Manufacturing Process 5. A face milling operation is used to machine 5 mm from the...
Industrial Manufacturing Process
5. A face milling operation is used to machine 5 mm from the top surface of a rectangular piece of aluminum 400 mm long by 100 mm wide. The cutter has four teeth (cemented carbide inserts) and is 150 mm in diameter. Cutting conditions are: v- 3 m/s, f 0.27 mm/tooth, and d 5.0 mm. Determine: (a) time to make one pass across the surface, and (b) metal removal rate during cutting.
Page 10 of 11 15 points A block of nickel alloy, 50 cm long and 20...
Page 10 of 11 15 points A block of nickel alloy, 50 cm long and 20 cm wide, is machined with slab-milling process at a feed rate of 0.025 cm/tooth and a depth of cut of 3.2 mm. The cutter has eight (8) straight cutting teeth, a diameter of 6.5 mm and rotates at 150 rpm. The specific energy of the workpiece (nickel alloy) is 113 W- min/cm3. Calculate The material removal rate. b) The power required, and The cutting...
Question 1 A turning operation is carried out on aluminum. Based on the specific energy values...
Question 1 A turning operation is carried out on aluminum. Based on the specific energy values in Table 20.2, determine material removal rate and cutting power in the operation under the following sets of cutting conditions: (a) Cutting speed 5.6 m/s, feed 0.25 mm/rev, and depth of cut 2.0 mm; and (b) cutting speed- 1.3 m/s, feed 0.75 mm/rev, and depth 4.0 mm. Question 2 Consider a turning operation performed on steel whose hardness 225 HB at a cutting speed...
PART 3: OPTIONAL PROBLEMS Vertical milling is used to machine the whole surface (20 x 150...
PART 3: OPTIONAL PROBLEMS Vertical milling is used to machine the whole surface (20 x 150 mm) of an aluminum block. The feed is along the longest length of the part. Use SI units for all your work. Tool: ø12.7 mm (ø0.500 in), 30 mm (1.181 in) long, 4 inserts Workpiece: 20 x 150 x 10 mm height (0.78 x 5.900 x 0.390 in height) a) Sketch the set up and list relevant information. Show any motion with an arrow....
2.(USCS units) A face milling operation is performed on the top surface of a steel block that is 12.0 in long by 3.0 in wide by 2.5 in thick. The milling cutter follows a path that is centered over the width of the block. It has five teeth and a 3.0 in diameter. Cutting speed-250 ft/min, feed- 0.006 in/tooth, and depth of cut -0.150 in. Determine (a) machining time and (b) maximum removal rate during the cut. (c) If an...
A face milling operation removes 4.0 mm from the top surface of a rectangular piece of aluminum that is 200 mm long by 60 mm wide by 75 mm thick. The cutter follows a path that is centered over the workpiece. It has four teeth and is 100 mm in diameter. Cutting speed = 2.5 m/s, and chip load = 0.27 mm/tooth. Determine (a) maximum metal removal rate during cutting in mm3/seconds (b) machining time in seconds. Cutter position at...
1. A face milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in long by 2.5 in wide. The milling cutter follows a path that is centered over the workpiece. It has five teeth and a 3.0 in diameter. Cutting speed = 250 ft/min, feed = 0.006 in/tooth, and depth of cut = 0.150 in. Determine (a) the actual cutting time to make one pass across the surface and (b) the maximum metal removal rate...
answer a) is 1.35 and b) 7.16 i want the answer for c Problem #4 A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in fong by 2.5 in wide. The helical milling cutter, which has a 3.0 in diameter and ten teeth, is set up to overhang the width of the part on both sides. Cutting speed is 125 ft/min, feed is 0.006 in/tooth, and depth of cut - 0.300 in.? Determine...
Industrial Manufacturing Process
5. A face milling operation is used to machine 5 mm from the top surface of a rectangular piece of aluminum 400 mm long by 100 mm wide. The cutter has four teeth (cemented carbide inserts) and is 150 mm in diameter. Cutting conditions are: v- 3 m/s, f 0.27 mm/tooth, and d 5.0 mm. Determine: (a) time to make one pass across the surface, and (b) metal removal rate during cutting.
Page 10 of 11 15 points A block of nickel alloy, 50 cm long and 20 cm wide, is machined with slab-milling process at a feed rate of 0.025 cm/tooth and a depth of cut of 3.2 mm. The cutter has eight (8) straight cutting teeth, a diameter of 6.5 mm and rotates at 150 rpm. The specific energy of the workpiece (nickel alloy) is 113 W- min/cm3. Calculate The material removal rate. b) The power required, and The cutting...
Question 1 A turning operation is carried out on aluminum. Based on the specific energy values in Table 20.2, determine material removal rate and cutting power in the operation under the following sets of cutting conditions: (a) Cutting speed 5.6 m/s, feed 0.25 mm/rev, and depth of cut 2.0 mm; and (b) cutting speed- 1.3 m/s, feed 0.75 mm/rev, and depth 4.0 mm. Question 2 Consider a turning operation performed on steel whose hardness 225 HB at a cutting speed...
PART 3: OPTIONAL PROBLEMS Vertical milling is used to machine the whole surface (20 x 150 mm) of an aluminum block. The feed is along the longest length of the part. Use SI units for all your work. Tool: ø12.7 mm (ø0.500 in), 30 mm (1.181 in) long, 4 inserts Workpiece: 20 x 150 x 10 mm height (0.78 x 5.900 x 0.390 in height) a) Sketch the set up and list relevant information. Show any motion with an arrow....
Most questions answered within 3 hours.
-
A 1400Kg sports car accelerates from rest to 90km/h in 7.0s.
What is the average power...
asked 2 seconds from now -
For the following reaction, 0.128 moles of
potassium hydrogen sulfateare mixed with
0.504 moles of potassium...
asked 3 hours ago -
1. What is the present value of $400, three years in the future
if the interest...
asked 4 hours ago -
The labor force minus the number of employed equals the number
of unemployed.
a. True
b....
asked 6 hours ago -
Determine the mass in units of grams [g] of 0.49 moles [mol]
of a new fictitious...
asked 6 hours ago -
A horizontal mass of M=5kg is on a spring and stretched to
x=0.5m when released from...
asked 7 hours ago -
26 of 50
"I have worked at the Arizona Humane Society for ten years, and
have...
asked 8 hours ago -
Compare and contrast zero based budgeting and incremental (or
base year) budgeting.
asked 8 hours ago -
4 pts 10. Which of the following hypothesis would be MOST
difficult to test experimentally? Group...
asked 8 hours ago -
A business owner makes 1,000 items a day. Each day he or she
contributes eight hours...
asked 8 hours ago -
A
circular loop in the plane of a paper lies inca0.65 T magnetic
field pointing into...
asked 8 hours ago -
A business owner is trying to decide whether to buy, rent, or
lease office space and...
asked 8 hours ago