A 6*12-in. concrete cylinder was tested under compression, and the ultimate load was calculated as 141,371.7...
A 6*12-in. concrete cylinder was tested under compression, and the ultimate load was calculated as 141,371.7 lb.
- Calculate the ultimate compressive strength of the cylinder in psi.
- A similar specimen with the same strength was initially loaded to 50 psi and strain was measured as 0.00050. After that, the specimen was loaded to 40% of its ultimate strength and the measured strain was 0.00078. Calculate the modulus of elasticity of concrete.
c. Under the same loading conditions stated in part (b), transverse strains at the mid-height of the specimen were measured as 1.2´10-5 and 1.8´10-5. Calculate the Poisson’s ratio of concrete.
Homework Answers
Add Answer to:
A 6*12-in. concrete cylinder was tested under compression, and
the ultimate load was calculated as 141,371.7...
Q. No.5: A concrete cylinder having a dimeter of 4 in. was tested in compression at...
Q. No.5: A concrete cylinder having a dimeter of 4 in. was tested in compression at concrete age of 28 days to find the compressive strength of concrete. The cylinder failed at a peak load of 91,280 lb. For this concrete determine: o Compressive strength of concrete e) o Modulus of elasticity (Ee o Modulus of rupture
A concrete cylinder 12 inches high is subjected to a compression test. At 5600 psi, the...
A concrete cylinder 12 inches high is subjected to a compression test. At 5600 psi, the strain is 0.0013 in/in. Determine (a) the change in length of the cylinder at 5600 psi and (b) the modulus of elasticity of the concrete cylinder.
A 6 x 12-in. concrete cylinder was tested to failure. The following loads and strains were...
A 6 x 12-in. concrete cylinder was tested to failure. The following loads and strains were recorded: Load, kips Strain 10-4 Load, kips Strain×10-4 0.0 12 24 36 48 60 0.0 1.2 2.0 3.2 5.2 7.2 72 84 96 108 95 82 10.0 13.6 18.0 30.0 39.0 42.0 a. Draw the stress-strain diagram of concrete and determine the maximum stress and corresponding strain b. Determine the initial modulus and secant modulus. c. Calculate the modulus of elasticity of concrete using...
Stress-strain curve represents the result of 6" x 12" concrete cylinders tested in compression. From the...
Stress-strain curve represents the result of 6" x 12" concrete cylinders tested in compression. From the results determine, • The approximate load causing the specified strength of the concrete • The tensile strength of the concrete per ACI 318-14 • The modulus of elasticity of concrete, based on: a. The appropriate ACI 318-14 expression b. the ACI 318-14's Secant approach 6 5 4 Stress, ksi 3 1 O 0.001 0.003 0.004 0.002 Strain
A concrete test cylinder made from a known design mix is loaded with P-200 kips and compresses by...
A concrete test cylinder made from a known design mix is loaded with P-200 kips and compresses by o.018 inch. a) Determine the strain developed in concrete b) Determine the axial compressive stress c) A contractor wants to use the same concrete design mix in a new construction project where the required compressive strength of concrete is 4000 psi. Would you approve the concrete mix? P= 200 kips S-0.018 st TEST
A concrete test cylinder made from a known design...
. Describe the response of concrete subjected to cyclic loading with the help of a graph. (Note: ...
. Describe the response of concrete subjected to cyclic loading with the help of a graph. (Note: Please plot a graph and then describe the effect of cyclic loading on strength and modulus of elasticity of concrete. You will not get credit if you cut and paste the graph from class notes). 2. Discuss why testing of concrete for direct tensile strength is difficult to achieve. What indirect test methods have been developed to assess the tensile strength of concrete?...
Cracking Moment (Uncracked Concrete Stage) Problem 1) Problem 2.6 (page 55, McCormac and Brown, gth Ed.)...
Cracking Moment (Uncracked Concrete Stage) Problem 1) Problem 2.6 (page 55, McCormac and Brown, gth Ed.) Note: Modify the total depth of the beam from 24" to 26" and the depth of the steel rebars from 21" to 23". Transformed Area Method (Concrete Cracked- Elastic Stresses Stage) Problem 2) Problem 2.13 (page 56, McCormac and Brown, 8th Ed.) Note: Make the following changes: Change fe to 5 ksi use the values and dimensions shown in the figure below 1) 2)...
Q. No.5: A concrete cylinder having a dimeter of 4 in. was tested in compression at concrete age of 28 days to find the compressive strength of concrete. The cylinder failed at a peak load of 91,280 lb. For this concrete determine: o Compressive strength of concrete e) o Modulus of elasticity (Ee o Modulus of rupture
A 6 x 12-in. concrete cylinder was tested to failure. The following loads and strains were recorded: Load, kips Strain 10-4 Load, kips Strain×10-4 0.0 12 24 36 48 60 0.0 1.2 2.0 3.2 5.2 7.2 72 84 96 108 95 82 10.0 13.6 18.0 30.0 39.0 42.0 a. Draw the stress-strain diagram of concrete and determine the maximum stress and corresponding strain b. Determine the initial modulus and secant modulus. c. Calculate the modulus of elasticity of concrete using...
Stress-strain curve represents the result of 6" x 12" concrete cylinders tested in compression. From the results determine, • The approximate load causing the specified strength of the concrete • The tensile strength of the concrete per ACI 318-14 • The modulus of elasticity of concrete, based on: a. The appropriate ACI 318-14 expression b. the ACI 318-14's Secant approach 6 5 4 Stress, ksi 3 1 O 0.001 0.003 0.004 0.002 Strain
A concrete test cylinder made from a known design mix is loaded with P-200 kips and compresses by o.018 inch. a) Determine the strain developed in concrete b) Determine the axial compressive stress c) A contractor wants to use the same concrete design mix in a new construction project where the required compressive strength of concrete is 4000 psi. Would you approve the concrete mix? P= 200 kips S-0.018 st TEST
A concrete test cylinder made from a known design...
. Describe the response of concrete subjected to cyclic loading with the help of a graph. (Note: Please plot a graph and then describe the effect of cyclic loading on strength and modulus of elasticity of concrete. You will not get credit if you cut and paste the graph from class notes). 2. Discuss why testing of concrete for direct tensile strength is difficult to achieve. What indirect test methods have been developed to assess the tensile strength of concrete?...
Cracking Moment (Uncracked Concrete Stage) Problem 1) Problem 2.6 (page 55, McCormac and Brown, gth Ed.) Note: Modify the total depth of the beam from 24" to 26" and the depth of the steel rebars from 21" to 23". Transformed Area Method (Concrete Cracked- Elastic Stresses Stage) Problem 2) Problem 2.13 (page 56, McCormac and Brown, 8th Ed.) Note: Make the following changes: Change fe to 5 ksi use the values and dimensions shown in the figure below 1) 2)...
Most questions answered within 3 hours.
-
Accounts Receivable
Sales
A/R Posting
Extended Sales Invoice
Packing Slip
Compare invoice to packing slip 2...
asked 2 minutes ago -
Michaella, age 23, is a full-time law student and is claimed by
her parents as a...
asked 2 minutes ago -
Why are polymers not typically casted into products?
asked 19 minutes ago -
When rolling a die 129 times, what is the probability of rolling
a 6 no more...
asked 36 minutes ago -
4. A call option currently sells for $7.75. It has a strike
price of $85 and...
asked 25 minutes ago -
1.
You need to prepare 10.0 liters of an acid aqueous solution with a
pH of...
asked 27 minutes ago -
Along an aggregate supply curve, if the level of output is less
than the natural level...
asked 28 minutes ago -
By 2025, annual consumption in emerging markets will total $30
trillion and contribute more than ________...
asked 33 minutes ago -
At what point does reformation cease to be a viable option for
those who are oppressed...
asked 37 minutes ago -
Place letters corresponding to amounts in the proper order for
lightest to heaviest samples:
a) 2100...
asked 41 minutes ago -
Consider the multicore processor with 6 heterogeneous cores
labelled C1, C2, C3, C4, C5, and C6....
asked 44 minutes ago -
Document system components according to standards and procedures
(Implement and hand over system components) IT administrative
asked 44 minutes ago