ZuoTi.Pro
Question

A flat composite wall consists of four layers of different materials (Concrete, Carbon steel, Kapok, and Masonry Brick). Each

engineering   Mechanical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

広enm al Gendue.huikt zk kcar tev, sicer = 54 W/.nk , k waenaty brideニ0.6 Shymk. Ruistance·te. Conducti vily. kA yhi A:uni13-2o ㄥ 127. 87S by A 27.87s 0.6S

0 0
Add a comment
Know the answer?
Add Answer to:
A flat composite wall consists of four layers of different materials (Concrete, Carbon steel, Kapok, and...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • A wall covering consists of four layers of insulation. The four layers are identical with all...

    A wall covering consists of four layers of insulation. The four layers are identical with all four having a thermal conductivity of .10 J/(s-m-Co). The thickness of each layer is .25m. The area of each of the layers is 100 m2. There is no gap of any kind between any of the four layers. The temperature on the outside of the wall is 100 Co. The heat conducted through the wall in 100 seconds is 1(104) Joules. Calculate the temperature...

  • • A wall of an industrial oven consists of three different materials, as depicted in Figure....

    • A wall of an industrial oven consists of three different materials, as depicted in Figure. • The first layer is composed of 5 cm of insulating cement with a clay binder that has a thermal conductivity of 0.08 W/m.K. • The second layer is made from 15 cm of 6-ply asbestos board with a thermal conductivity of 0.074 W/mK (W/m.°C). • The exterior consists of 10-cm common brick with a thermal conductivity of 0.72 W/mK (W/m °C). • The...

  • is the second floor of a four-story building. a flat Consider the floor framing plan shown...

    is the second floor of a four-story building. a flat Consider the floor framing plan shown below. Thi The design floor live load is 90 psf. The design roof live load is 20 psf. The structure has roof G1 G4 /2 G2 GS 2o G3 FLOOR FRAMING PLAN Assume that the floor between Beams B7 and B8 is supported directly by these two beams only (not by Girders G2 and G3). Beam B7 has a self-weight of 30 plf. The...

  • Ques 2: An open ended cylindrical steel-pile of 400mm diameter and 6.35mm wall thickness is drive...

    Provide a detailed step by step solution Ques 2: An open ended cylindrical steel-pile of 400mm diameter and 6.35mm wall thickness is driven into soft normally consolidated clay. Ground water level is at the ground surface. Applied load on the pile is 200kN and factor of safety factor of 3 is required. Determine the minimum length of the pile by analyzing long term and short term stability. Given: Cu-40kPa, &0'-23°, and Y. 18.9kN/m Ques 3: A group of 16 square...

  • summarizr the followung info and write them in your own words and break them into different...

    summarizr the followung info and write them in your own words and break them into different key points.   6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...

  • summatize the following info and break them into differeng key points. write them in yojr own...

    summatize the following info and break them into differeng key points. write them in yojr own words   apartus 6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT