Match the equation to the corresponding system response 0.06 0.04 0.02 A.10mx + 3x + 25x...
Figure below shows the time response of the system mechanical figure above to a force in step of 8.5 N.
Following the analysis of the system in the figure above
a) Determine the transfer function X(s)/F(s) of the system and give the standard form of the latter.
b) Based on the response of this system at 8.5 N, determine the , and parameters of the mechanical system.
c) By combining the results found previously, determine the value of the three...
Stress-Strain Diagram-2 Stress Strain Diagram 120 100 80 60 40 20 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2 0.22 e(in/in) 5) Refer to Stress-Strain Diagram 2. If a rod of this material has an original diameter of 0.5 in and an original length (unloaded) of 144 in, how long was the rod at rupture? A) 145 in B) 29 in C) 173 in D) 164 in
1) A causal discrete-time system is described by the difference equation, y(n) = x(n)+3x(n-1)+ 2x(n-4) a) What is the transfer function of the system? b) Sketch the impulse response of the system
The power versus time for a point on a string (μ = 0.06
kg/m) in which a sinusoidal traveling wave is induced is
shown in the following figure. The wave is modeled with the wave
equation y(x, t) = A sin[(25.43 m−1)x − ωt]. What are
the frequency (in Hz) and amplitude (in m) of the wave?
The power versus time or a point on a string μ 0.06 kg/m n which a sinusoidal traveling wave sind ce s snow...
3. The input and output corresponding to the steady (vibratory) response of a first order system have been recorded below. (a) Use the phase difference to find the time constant of the system. (b) Use the magnitude ratio between both curves to find the time constant of the system and compare your answer to that of part (a) if the equation is known to be ai + bx = Csin(wt) where the input is Csin(wt), the output is x, and...
Apr. 17, 2019 Name PROBLEMİ: (30%) (a) Match the following unit step response curves with the system dynamic equations. (15%) Step Rosponse 2.5 1.5 0.5 10 Time (seconds) (b) A 2nd-order system is given a step input. Make an accurate drawing of the complex plane that shows the pole locations corresponding to no overshoot, and 2% settling time between 2 and 3 seconds. (You need to show the calculation) (15%)
Apr. 17, 2019 Name PROBLEMİ: (30%) (a) Match the following...
Assume the following closed-loop system with a PID controller. Match the step responses with the appropriate controller parameters. R(s) + PID Y(s) Controller G(s) 1. Step Response 1.5 data 0.5 0 10 40 50 20 30 Time (seconds) Kp = 2, Td = 1, Ti = 5 2. Step Response 1.5 =1, Kp = 5, Td Ti = 5 0.5 D 10 40 50 Кр = 10, Td = 1, T = 5 20 30 Time (seconds) Step Response 3....
Question 12 (4 points) Solve the System of Equations 2x - 5y = 13 3x + 4y = –15 O (-1,-3) 0 (-3,1) (3,1) (1,3) Question 13 (4 points) Solve the System of Equations 7x + 9y = -34 - 4x - 64 = 20 Question 14 (4 points) If f(x) = (3)" then what is f(-3)? O =27 0 0 0 Question 15 (4 points) A bottle of 140 super-vitamins costs $20. If the cost varies directly with the...
Spring mass damper system with forced response, the forced system given by the equation For damping factor:E-0.1 ; mass; m-| kg: stiffness of spring; k-100 Nm; f-| 00 N; ω Zun; initial condition: x (0)-2 cms; r(0) = 0. fsincot Task Marks 1. Write down the reduced equation into 2first orderns Hand written equations differential equations 2. Rearrange equation (1) with the following generalized equation 250, x+osinor calculations 3. Calculate the value of c calculations Hand calculations 4. Using the...
a.
d.
Match the following z-plane diagrams to their corresponding difference equations 1.5 1.5 0.5 .' 05 05 05 Real Part Real Pat 1.5 1.5 0.5 0.5 05 05 ' Real Part Real Part 1.5 1.5 0.5 05 Real Part Real Part Difference Equation Options: Equation 1: y[n] 0.5yIn-1] + xm Equation 2: yn0.9yfn - 1] + 0.5x[n +0.5xn -1] Equation 3: y[n] =-0.9y[n-1] + 0.5z[n] _ 0.5z[n-1] Equation 4: y[n] = z[n] + x[n-1] + z[n-2 + z[n-3] Equation...