Option ' e' correct, because
A combination cycle power plant relies on the simple fact that a gas turbine produces both power & hot exhaust gases. As the power is channeleled to a generator, the hot gas are used to produce steam. The steam runs a steam turbine to produce extra power.
Question 2 Which of the following has the highest thermal efficiency? O a simple steam turbine...
Problem4 (a) (40 points) A combined gas-steam powe cycles. The ideal Brayton and Rankine plant operates on Rankine cycle has a reheater. The Brayton cycle operates on a gas- of the gas-turbine cycle 1400 K The 15MPa to ercooling, reheating, and regeneration cycle. The pressure ratio 300 K for compressor stages is do Air enters compressors a combustion gases leaving the lower pressure gas turbine are used to heat the steam at C in a heat exchanger. The combustion gases...
please solve the problem, it is thermo-design problem,
please do in details, thank you
Combustor Gas turbine :Compressor- Turbine Air inlet- 7 Heat-recovery steam generator Turbine Vapor cycle W) Pump Condenser Cooling water Figure 1: Combined gas turbine-vapor power plant Consider Figure 1 above. The following information is given a. p- 14.7 psia, T 540 °R b. P/p1 12.0 С. Т,-2500,"R d, P,-14.7 psia, Ts-700. "R (Rankine) e. P 1000. psia f. P 1.00 psia, x>0.85 or superheated The isentropic...
a) The temperature of the
steam at the turbine exit
b) Thermal efficiency of the cycle
c) the mass flow rate of the steam
Part 2 of 4 Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and...
power plant
3- A combined power plant consisting of a simple open cycle gas turbine unit, using air as the working fluid (neglect fuel mass flow rate), and a steam turbine is to be designed such that the heat rejected at the gas turbine unit is to be utilized to produce steam at the generator for the steam turbine. The exhaust air leaving the generator is at (200 C°). Draw a simple sketch for the plant and the (T-s) diagram...
1. Determine the thermal efficiency and the required steam flow rate [kg/s] for a reheat regenerative steam power plant which is to produce 200 MW of electricity. The turbine drives a generator with an efficiency of 94%. The turbine inlet conditions are 160 bar and 590 C; after reheat, the steam is at 100 bar and 590 C; one closed heater is at 30 bar; an open feedwater heater is at 1.5 bar, and the condenser pressure is 0.10 bar....
The gas turbine cycle of a gas-steam combined cycle power plant has a pressure ratio of 12. The air enters the compressor at 310 K and 100 kPa (1) and the turbine at 1400 K (3). The combustion gases leaving the gas turbine (4) are used to heat the steam to 12.5 MPa up to 500 °C (6) in a heat exchanger. The flue gas exits the heat exchanger (5) at 247 °C. The steam is expanded in a high...
Consider the combined gas-steam power cycle,The topping cycle is a gas-turbine cycle that has a pressure ratio of 8.Air enters the compressor at 300K and the turbine at 1300K.The isentropic efficiency of the compressor is 80 percent, and that of the gas is 85 percent.The bottoming cycle is a simple ideal Rankine cycle operating between the pressures limits of 7 MPa and 5 KPa.Steam is heated in a heat exchanger by the exahust gases to a temperature of 5000C.The exhaust...
Problem 2/2 (50%) -The gas-turbine cycle of a combined gas-steam power plant has a pressure ratio of 12. Air enters the compressor at 310 K and the turbine at 1400 K. The combustion gases leaving the gas turbine are used to heat the steam at 12.5 MPa to 500 C in a heat exchanger. The combustion gases leave the heat exchanger at 247"C. Steam expands in a high pressure turbine to a pressure of 2.5 MPa and is reheated in...
A combined gas-steam power plant uses a simple gas turbine for
the topping cycle and a simple Rankine cycle for the bottoming
cycle. Atmospheric air enters the compressor at 101 kPa and 20 °C,
and the maximum gas cycle temperature is 1100 °C. The
compressor pressure ratio is 8. The gas stream leaves the heat
exchanger at the saturation temperature of the steam flowing
through the heat exchanger. Steam enters the heat exchanger at a
pressure of 6 MPa and...
Energy Convertion
hello, please help me quickly please please
thank you
Question B (15 marks) You are to analyze a combined cycle that consists of a gas (air) turbine cycle (top) ttom). The gas cycle has the following operating conditions: inlet pressure to compressor one bar inlet temperature-300 K operating pressure ratio-12 Maxmum allowable temperature 1150 °C adiabatic efficiency for compressor 0.83 adiabatic efficiency for turbine-0.87 - - The exhaust leaves stack at 120 °C after vaporizing water in the...