Power system operation and control
The positive-sequence reactances for the power system shown in Figure 10.31 are in per unit on a common MVA base. Resistances are neglected and the negative-sequence impedances are assumed to be the same as the positive-sequence impedances. A bolted line-to-line fault occurs between phases b and c at bus 2.
Before the fault occurrence, all bus voltages are 1.0 per unit. Obtain the positive-sequence bus impedance matrix.
Find the fault current, the three-phase bus voltages during fault, and the line currents in each phase.
(a) Use hand calculation
Homework Answers
Request Answer!
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
can you calculating this question and explain why? thanks The ratings and sequence reactances of the components for...
can you calculating this question and explain why?
thanks
The ratings and sequence reactances of the components for the power system shown in Figure 2 are given in Table 1. The pre-fault voltage is 1/0° per unit (pu). Bus 8 L3 Bus 1 T1 Bus 4 T2 Bus 2 Bus 5 L1 L2 G1 Bus 3 T3 Bus 7 Bus 6 D.6975 Figure Draw the per unit impedance sequence networks and determine the per unit (a) Thevenin impedances of the...
A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y...
A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance Xn 0.05 per unit on the motor base. Assume that Pre-fault voltage is takin as VF-1.0 ,0° per unit and Pre- fault load current and Δ-Y transformer phase shift are neglected In the...
The one-line diagram of a three-bus power system is shown in Figure 4. All impedances are...
The one-line diagram of a three-bus power system is shown in
Figure 4. All impedances are
expressed in per unit on a common MVA base. All resistances and
shunt capacitances are
neglected. Information on each component in this system is given
below:
• Each generator is represented by an emf
behind the sub-transient reactance of j0.045
and their neutrals are connected to the
ground.
• Line 1-2 has reactance of j0.88
• Line 2-3 has reactance of j0.65
• Line...
2. A single-line diagram of the power system considered is shown in Figure P2a, where negative-...
2. A single-line diagram of the power system considered is shown in Figure P2a, where negative- and zero-sequence reactances are also given. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance Xn = 0.05 per unit on the motor base. The per-unit zero-, positive and negative-sequence networks on a 100-MVA is shown in Figure P26, 13.8-kV base in the zone of the generator. a. Reduce the sequence networks to their...
Note: # 1 states line to line fault occurs, while # 2 states double line to...
Note: # 1 states line to line fault occurs, while # 2 states double line to ground fault occurs Please explain the solution thoroughly with diagrams The positive, negative, and zero sequence reactances of a 15-MVA, 11-kV, 3ph, wye-connected generator are 11%, 8% and 3%, respectively. The neutral of the generator is grounded, and the generator is excited to the rated voltage on open circuit. A line-to-line fault occurs between phases b and c of the generator while phase a...
The component parameters for the power system shown in Figure 2 are given in Table 1. The pre-fau...
The component parameters for the power system shown in Figure 2 are given in Table 1. The pre-fault voltage is 120° pu and Zx-j0.1 pu. Table 1 Ratings X2-Xi (pu)Xo (pu) 0.05 0.10 0.20 0.20 Components G1, G2 200 MVA, 20 kV 0.10 0.10 0.10 0.10 T1, T2, T3200 MVA, 20/200 kV L1 200 MVA, 200 kV し2 200 MVA, 20 kV (a) Draw the three sequence networks and determine the per-unit Thevenin impedance of each sequence network seen from...
Consider the 3-bus power system single diagram below. A bolted three phase fault occurs at bus...
Consider the 3-bus power system single diagram below. A bolted three phase fault occurs at bus 3. Using bus impedance matrix calculate the following: 1 j0,2 j0,5 0,3 A2 2 3 A3 j0,3 0,6 j0,2 1.1 1.2 1.3 Fault current Bus voltages Line currents during the fault.
QUESTION 1: Consider the 3-bus power system single diagram below. A bolted three phase fault occurs...
QUESTION 1: Consider the 3-bus power system single diagram below. A bolted three phase fault occurs at bus 3. Using bus impedance matrix calculate the following: j0,2 j0,5 0,3 A2 2 3 A3 0,3 j0,6 j0,2 1.1 Fault current Bus voltages Line currents during the fault. 1.3
Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which ...
Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which is 20% of the total line 2 length from Bus B Fault MVA 1524.20471 Three-phase fault level in MVA at bus A SPFL (kA) 8 MVA1 MVA2 X1 (96 X2 (96) R1 (2) R2 (Q) z' (Q) Zo (2) Rf (Q) Single phase to ground fault level (kA) at bus A Transformer 1 MVA...
The zero-, positive-, and negative-sequence bus impedance matrices for a three bus power system are given...
The zero-, positive-, and negative-sequence bus impedance matrices for a three bus power system are given below 5. T0.10 0.15 0.121 Bu0.15 0.10 0.08 pu [0.16 0.10 0.15] Lo.15 0.14 0.30 0.12 0.08 0.35 ZBus ZBus0.10 0.20 0.14 pu Determine the per unit fault current and the bus voltages during fault for (a) A bolted three-phase fault at bus 2. (b) A bolted single line-to-ground fault at bus 2. (c) A bolted line-to-line fault at bus 2 (d) A bolted...
can you calculating this question and explain why?
thanks
The ratings and sequence reactances of the components for the power system shown in Figure 2 are given in Table 1. The pre-fault voltage is 1/0° per unit (pu). Bus 8 L3 Bus 1 T1 Bus 4 T2 Bus 2 Bus 5 L1 L2 G1 Bus 3 T3 Bus 7 Bus 6 D.6975 Figure Draw the per unit impedance sequence networks and determine the per unit (a) Thevenin impedances of the...
A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance Xn 0.05 per unit on the motor base. Assume that Pre-fault voltage is takin as VF-1.0 ,0° per unit and Pre- fault load current and Δ-Y transformer phase shift are neglected In the...
The one-line diagram of a three-bus power system is shown in
Figure 4. All impedances are
expressed in per unit on a common MVA base. All resistances and
shunt capacitances are
neglected. Information on each component in this system is given
below:
• Each generator is represented by an emf
behind the sub-transient reactance of j0.045
and their neutrals are connected to the
ground.
• Line 1-2 has reactance of j0.88
• Line 2-3 has reactance of j0.65
• Line...
2. A single-line diagram of the power system considered is shown in Figure P2a, where negative- and zero-sequence reactances are also given. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance Xn = 0.05 per unit on the motor base. The per-unit zero-, positive and negative-sequence networks on a 100-MVA is shown in Figure P26, 13.8-kV base in the zone of the generator. a. Reduce the sequence networks to their...
The component parameters for the power system shown in Figure 2 are given in Table 1. The pre-fault voltage is 120° pu and Zx-j0.1 pu. Table 1 Ratings X2-Xi (pu)Xo (pu) 0.05 0.10 0.20 0.20 Components G1, G2 200 MVA, 20 kV 0.10 0.10 0.10 0.10 T1, T2, T3200 MVA, 20/200 kV L1 200 MVA, 200 kV し2 200 MVA, 20 kV (a) Draw the three sequence networks and determine the per-unit Thevenin impedance of each sequence network seen from...
Consider the 3-bus power system single diagram below. A bolted three phase fault occurs at bus 3. Using bus impedance matrix calculate the following: 1 j0,2 j0,5 0,3 A2 2 3 A3 j0,3 0,6 j0,2 1.1 1.2 1.3 Fault current Bus voltages Line currents during the fault.
QUESTION 1: Consider the 3-bus power system single diagram below. A bolted three phase fault occurs at bus 3. Using bus impedance matrix calculate the following: j0,2 j0,5 0,3 A2 2 3 A3 0,3 j0,6 j0,2 1.1 Fault current Bus voltages Line currents during the fault. 1.3
Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which is 20% of the total line 2 length from Bus B Fault MVA 1524.20471 Three-phase fault level in MVA at bus A SPFL (kA) 8 MVA1 MVA2 X1 (96 X2 (96) R1 (2) R2 (Q) z' (Q) Zo (2) Rf (Q) Single phase to ground fault level (kA) at bus A Transformer 1 MVA...
The zero-, positive-, and negative-sequence bus impedance matrices for a three bus power system are given below 5. T0.10 0.15 0.121 Bu0.15 0.10 0.08 pu [0.16 0.10 0.15] Lo.15 0.14 0.30 0.12 0.08 0.35 ZBus ZBus0.10 0.20 0.14 pu Determine the per unit fault current and the bus voltages during fault for (a) A bolted three-phase fault at bus 2. (b) A bolted single line-to-ground fault at bus 2. (c) A bolted line-to-line fault at bus 2 (d) A bolted...
Most questions answered within 3 hours.
-
The marketing class at CSUS had an average score of 150. An
educational analyst determined that...
asked 15 minutes ago -
Justin Case has purchased a $250 000 home by putting 20 % down
and taking out...
asked 25 minutes ago -
1. In a labor market, marginal cost for a firm is
____________.
a. recruiting cost
b....
asked 57 minutes ago -
On January 1, 2019, ABC Company issued $60,000,000 of 20-year,
10.5% bonds when the market rate...
asked 1 hour ago -
39.4% of US homes continue to use a landline in addition to cell
phone service. 3...
asked 2 hours ago -
Starting with benzene, synthesize 1-phenyl-1-butyne.
Show intermediates and reagents.
asked 2 hours ago -
Create a 32-run crossed array design with six control factors
and two noise factors such that...
asked 3 hours ago -
A 500g sample of sand from source A has the following amounts
retained on each sieve....
asked 3 hours ago -
In
your own words, please explain the essay by John Keynes wrote "The
End of Laissez...
asked 3 hours ago -
How are the matrix and pixels related? Why are smaller
pixels better for diagnostic quality?
asked 3 hours ago -
2. An AC generator has 80 rectangular loops on
its armature. Each loop is 11 cm...
asked 3 hours ago -
Please help me with this question. Consider Aldi’s current and
potential geographic markets (see Exhibit 4...
asked 3 hours ago