The time function (t) is given by sin(Wt) 2(t) = A- (a) Sketch this function, showing...
number 2 ECE 300 Continuous-Time Signals and Systems H(jø π/2 Plot the spectrum Z (jø) of the filtered input signal z(), the spectrum Z, (jo) of the sampled signal z.(t), and the spectrum Y(ja) of the reconstructed signal y(t). Show clearly how the output spectrum Y (ja) differs from the original spectrum G(jo) C. Which system, A or B, produces less distortion between the input g(t) and the output y(4) or ()? Explain. You can measure distortion by finding the...
Consider a sampler which samples the continuous-time input signal x(t) at a sampling frequency fs = 8000 Hz and produces at its output a sampled discrete-time signal x$(t) = x(nTs), where To = 1/fs is the sampling period. If the sampled signal is passed through a unity-gain lowpass filter with cutoff frequency of fs/2, sketch the magnitude spectrum of the resulting signal for the following input signals: (a) x(t) = cos(6000nt). (b) x(t) = cos(12000nt). (c) x(t) = cos(18000nt).
2.7.5 The impulse response of a continuous-time LTI system is given by h(t) = f(t) - et u(t). (a) What is the frequency response H (w) of this system? (b) Find and sketch H(w). (c) Is this a lowpass, bandpass, or highpass filter, or none of those? 2.7.6 The impulse response of a continuous-time LTI system is given by h(t) = S(t – 2). (This is a delay of 2.) (a) What is the frequency response H (w) of this...
8. The input r(t) and output y(t) of a transfer function block are sin(wt) and A sin(at +) respectively and ti are shown in the following figure. Determine the most suitable values for A and . a. A = 1.67 and $ = 45° b. A = 1.67 and $ = -45° C. A = 0.6 and $ = 45° d. A = 0.6 and 6 = -45° 9. Routh criterion is applied to check the stability of polynomials +s...
1. Given a baseband signal m(t) sin(1000mt) cos(3000nt) + cos(3700nt a. Sketch the spectrum of m(t) (Hint. sin(a) cos(b) 0.5 sin(a +b) +0.5sin a-b)) b. Sketch the spectrum of DSB-CS signal m(t)cos(10000mt) C ldentify the upper sideband {USB) and lower sideband (LSB) spectra d. Give the black diagram of the receiver to receive DSB-CS signal in (b). 2. baseband signal m(r)--0.5 + Σ..小(t-n)-u(t-0.5-n)] where ult) is the Given unit step function, an amplitude modulated signal is as SAM 107+ m(0cos...
Question 5 (a) The impulse response of a discrete-time filter is given as, hin) 0.56n-1] +n-2)0.56 n -3]. i. Derive the filter's frequency response; 11. Roughly sketch the filter's magnitude response for 0 ii. Is it a low-pass or high-pass filter? Ω 2m; (b) A continuous-time signal se(t) is converted into a discrete-time signal as shown below. s(t) is a unit impulse train. s(t) x,) Conversion into x(1) __→ⓧ一ㄅㄧ-discrete-time sequence ー→ xu [n] The frequency spectrum of ap (t) is...
Figure 2.4 shows a block diagram that consists of Device A with a transfer function of Vo1(t) = 1 + vi(t)2 and a Band Pass Filter that has a cutoff frequency of 6 kHz and 12 kHz. The input signal to the device is a 8 V sinusoidal signal Amplitude 8V Vot(t) Band Pass Device A Vo2(t) Time Vo1(t) 1vi(t) Filter 0.2ms Input signal, vi(t) Fiqure 2.4 State the expression of the input signal, vi(t) given that the signal is...
aliasing? A continuous-time system is given by the input/output differential equation 4. H(s) v(t) dy(t) dt dx(t) + 2 (+ x(t 2) dt (a) Determine its transfer function H(s)? (b) Determine its impulse response. (c) Determine its step response. (d) Is the stable? (a) Give two reasons why digital filters are favored over analog filters 5. (b) What is the main difference between IIR and FIR digital filters? (c) Give an example of a second order IIR filter and FIR...
Home-Work 5 All questions carry equal points. Don't forget to highlight your final answers 25 uestion # 1 Use table to find Fourier transform. Sketch the magnitude response and phase response (i) x(t) Cos(1000t) (ii) x(t) 13Cos(100t)- 7Sin(500t) (iv) x(t) rect To (v) xo)-rect ()Cos(10001) (v) x(o) -ret)Cos(000t) Question # 2 Let h(t) be a linear time invariant system, with the following transfer function s + 1 000m (a) Find H(w) (b) Sketch the magnitude and phase response of H(w)...
Digital Signal Processing QUESTION SIX A digital filter system has a transfer function given by 1-0.4z-1 T(z) = 1 + 0.2z-2 a) Draw the z-domain version of the block diagram for the filter 110) Derive an expression for the output sequence yin], in terms of the input b) sequence, xla], and delayed input and output sequences 10 151 e) Find the unit sample response for the filter (first three terms only) QUESTION SIX A digital filter system has a transfer...