Consider a cylinder of length L and cross-sectional area A made up of some material. How is the stiffness (Young’s modulus Y) of the material this cylinder is made of related an effective spring constant k for this specific cylinder.
A.) Y = k L2 / A
B.) Y = k L/A <--- This is the correct answer but I do not understand why.
C.) Y = k A L2
D.) Y = k L A
E.) Y = k L/A2
Consider a cylinder of length L and cross-sectional area A made up of some material. How...
Figure < 1 of 1 Consider, for instance, a bar of initial length L and cross-sectional area A stressed by a force of magnitude F. As a result, the bar stretches by AL (Figure 1) Let us define two new terms: • Tensile stress is the ratio of the stretching force to the cross-sectional area: stress = 5 • Tensile strain is the ratio of the elongation of the rod to the initial length of the bar strain= 41 It...
A wire of unknown material with a cross-sectional area of 1 mm^2 and an unstretched length of 0.5 m is stretched through the application of known forces. From the plot of force as a function of Delta L in the figure, the Young's modulus of the material is: A. 4 times 10^10 N/m^2 B. 80 N/m^2 C. 40 N/m^2 D. 8 times 10^10 N/m^2 E. none of the above
One copper wire has a cross sectional area of A and resistance R and length L. A second copper wire has a length L and cross-sectional area 2A. What is the resistance of the second wire in terms of R? R/2 R 2R 4R Some other value
3. 2090] Consider a uniform bar of Young's modulus E, cross-sectional area A, moment of inertia density p, length L, with an attached end mass, m, connected to a rigid wall via a linear spring of spring constant, k, see Figure. Let the longitudinal vibration of the bar be Wa.f). (a) [4] Write down the boundary conditions. m E, p Boundary condition at x 0 Boundary condition at x L (b) [81 Derive the equation for the natural frequency (c)...
A wire of length L and cross-sectional area A has resistance R. What will be the resistance Rstretched of the wire if it is stretched to twice its original length? Assume that the density and resistivity of the material do not change when the wire is stretched.
A block of material with a cross-sectional area of 15 cm2 and length of 8.0 cm is at hand. A temperature difference of 30 ̊C is established and maintained across the block. Find the rate of heat flow through it if: (2 marks) The material is copper (K = 397 Js-1m-1C-1). The material is air (K = 0.0234 Js-1m-1C-1). The material is wood (K = 0.08 Js-1m-1C-1).
A wire of length L and cross-sectional area A has a resistance of 5 Ω. What is the resistance if the same amount of material is used to make a wire triple as long?
Consider a steel guitar string of initial length 2.00m and cross-sectional area A = 0.500mm^2. The Young s modulus of the steel is 2.0 times 10^11 N/m^2. How far would such a string stretch under a tension of 1500 N?
Question 3 The structure shown in Figure Q(3) is a two-bar truss with spring support. Both bars have modulus of elasticity and cross-sectional area of E- 210 GPa and A -5.0 x10 m. Bar one has a length of 5 m and bar two a length of 10 m. The spring stiffness is k -2000 kN/m. CVE 4303(F) Page 2 of 4 Determine (a) the stiffness matrix for each of the three elements (15 marks) (b) the normal stresses in...
Question 4 1 pts A wire made from a composite material is shaped into a cylinder and is stretched by a machine pulling in opposite directions at the two ends of the wire. The wire has an initial length of 1.20 m and an initial cross-sectional area of 9.00 x 10-6m2. If a force of 450 N stretches it by 2.1 mm and the wire returns to its original shape after being stretched, what is the Young's Modulus of the...