Problem 2: A photo of a gearbox and its schematic are shown in the figure. The...

Question

Question

Answer 1

Answer #1

NIE N3 = 100 teeth N2 N4 = 150 teeth he ha v=9000 rpm ons P= 1 KN Greas ratio- N2 Ny s 150 x 150 , 2.25) V3 loo a 100 na = Ne

Answer 2

Similar Homework Help Questions

Output input 2. The gearbox in the diagram for problem 1 receives an input power of 10 kW, at a s...

output input 2. The gearbox in the diagram for problem 1 receives an input power of 10 kW, at a speed of 40. The gears are spur gears (ignore the helix angle on the teeth in the figure), have a module of 5 mm/tooth, and the pressure angle is 20. Assume all shafts lie in the same plane. Assume the gearbox is reasonably efficient, so losses can be neglected for this analysis. (a) Determine the minimum inside dimension of the...
In the gear train shown below, the pinion 2 is the driver, and gear 5 is...

In the gear train shown below, the pinion 2 is the driver, and gear 5 is the output gear. All gears are spur gears has a module of 2.5mm and pressure angle of 200. The number of gear teeth are: N2 - 14, N3 - 84, N4 - 14, N5 - 70 teeth. The gear set transmits the power of 1.5KW at a constant angular velocity of XX rev/min. Where XX is the last two digits of your University ID...
(b) Fig Q1 shows a two-stage spur gearbox. The input shaft is coupled to a motor....

(b) Fig Q1 shows a two-stage spur gearbox. The input shaft is coupled to a motor. The shaft “b” turns freely in bearings C and D, except for the gear-tooth forces. Assuming 100% gear efficiency, determine the resultant radial loads applied to bearings C and D, and sketch the shaft "b" as a free body in equilibrium. (28 Marks) (Total 33 Marks) INPUT 22 TEETH m = 5 mm 0 = 20 24 TEETH SHAFT"b 18 TEETH IDLER 66 TEETH...

You work for a gearbox company and have been charged with helping to design a geared...

You work for a gearbox company and have been charged with helping to design a geared countershaft for a speed reducing gearbox. The gearbox consists of a compound reverted gear train as shown below and is to be designed for an exact 16:1 speed reduction ratio. The input motor provides 10-horsepower which is carried through the gear train and operates at a speed of 2,000 rpm. You are asked to consider spur gears with a 20° pressure angle and 4...
211 301 35T 24T In the gearbox shown beside, input #1 is 800 rpm cw and...

211 301 35T 24T In the gearbox shown beside, input #1 is 800 rpm cw and input #2 is 400 rpm cw,then 13. (3 point) The output in the gearbox is rotating at: a) 640 rpm b) 1080 rpm c) 1180 rpm d) 1380 rpm Input #1 Output 800 rpm Input #2 x 14. (1 point) the direction of the output drum is a) cw b) ccw c) undetermined d) both directions 400 rpm E H 50T 32T 30T 431...
please show all work 4. Given an Epicyclic gearbox that has a fixed Sun gear “D",...

please show all work 4. Given an Epicyclic gearbox that has a fixed Sun gear “D", and the output gear “C” has 300 Teeth, Planet gears have 30 Teeth, the input is Arm “A”. Given that the input torque is 100 N.m., input speed of 1250 rpm and the efficiency of the gearbox is 70%. Calculate the number of teeth on the sun gear and the ratio of the gearbox. Also Calculate the Fixing Torque.

A gearbox is required to transmit 3.5 kWh from a shaft rotating at 200 rpm. The...

A gearbox is required to transmit 3.5 kWh from a shaft rotating at 200 rpm. The desired output speed is approximately 90 rpm. The input shaft is on the horizontal axis and the output shaft is on the vertical axis. Draw gear arrangement and select suitable gears for it. May draw multiple different arrangements and explain why.
please solve and show all steps D 5. Given a Compound Epicyclic gearbox that has the...

please solve and show all steps D 5. Given a Compound Epicyclic gearbox that has the following gears, a. Gear C = Gear E = 100 Teeth b. Gear B = Gear D = 200 Teeth Where input is Arm A and output is Gear E. Given the input torque is 100 N.m., input speed is 1000 rpm and gearbox efficiency is 75% Calculate the Gear box ratio, & the fixing/holding torque. E E B
UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves...

UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves as the input to the train. The sun (gear 1) serves as the output from the train and has a 1.0-in. pitch diameter with a diametric pitch of 20. Gear 3 has 45 teeth and gear 4 has 20 teeth Gear 5 has 30 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6),...

Can you please show me a detailed solution to this problem.? A compound reverted spur gear...

Can you please show me a detailed solution to this problem.? A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) |If all the gears are cut with 20° full-depth system....