The strings AB and AC connect to the 6-1b ball A to the vertical shaft. When...
Problem 3.18 A small ball A of mass mis con- nected to a vertical shaft at O by a string of length I. The system is initially at rest, with the pendulum in contact with the shaft. The shaft is then slowly set in rotation to reach a constant angular velocity w. Neglect the size of the balls and the diameter of the shaft, that is, O is on the axis of the shaft. a. Show that the line OA...
4. -2 points PSE6 6.P.011 My Notes A 3.90 kg object is attached to a vertical rod by two strings as in Figure P6.11. The object rotates in a horizontal circle at constant speed 7.10 m/s. 00 m 3.00 m 00 m Figure P6.11 (a) Find the tension in the upper string (b) Find the tension in the lower string
The plate has a mass of 6 kg and is welded to the fixed vertical shaft, which rotates at the constant speed of 12 pi rad/s. Define the reaction forces at both bearings supports at the instant shown. 100 100 mmmm -200 mm- 45° -200 mm- 0
Rod AB is attached to the rotating arm using ball-and-socket joints. If AC is rotating with a constant angular velocity of -0.3 rad/s about the pin at c, determine the angular velocity of link BD at the instant shown. Use the right-hand rule to interpret the direction of angular velocities. Report your answer with at least two decimal figure accuracy and include the unit. АС 1.5 ft 30 6 Ft 2 Ft
A 0.19-kg ball on a stick is whirled on a vertical circle at a constant speed. When the ball is at the three o’clock position, the stick's tension is 18 N. Find the tension in the stick when the ball is (a) at the twelve o’clock and (b) at the six o’clock positions.
A 0.18-kg ball on a stick is whirled on a vertical circle at a constant speed. When the ball is at the three o'clock position, the stick's tension is 19 N. Find the tension in the stick when the ball is (a) at the twelve o'clock and (b) at the six o'clock positions. (a) = (b) T=
1a. 1b. 1c. A uniform solid ball rolls smoothly along a floor, then up a ramp inclined at 24.1. It momentarily stops when it has rolled 2.40 m along the ramp. What was its initial speed? NumberT4.38 Unitsm's A certain gyroscope consists of a uniform disk with a 33.0 cm radius mounted at the center of an axle that is 11.0 cm long and of negligible mass. The axle is horizontal and supported at one end. If the disk is...
3. A ball of mass m is attached to a vertical pole with a length of string L and spun with a constant speed v in a horizontal circle. a. Draw a free body diagram of the ball below: (5) ( b. Write expressions for Newton's 2nd Law in the x- and y-directions. (20) Assume that m = 3.50 kg, and the speed of the ball is 6.50 m/s. c. Find the magnitude of the tension in the string. (5)...
The crank OA rotates in the vertical plane with a constant clockwise angular velocity ωo=4.5 rad/s. For the position when OA is horizontal, (a) determine the angular acceleration of the uniform 10 kg slender bar AB and the horizontal and vertical components of the acceleration of its center of mass. Use the methods of kinematics (Ch 16) to establish both the magnitude and direction → or ← for aG and; CW or CCW for αAB) of each variable. (b) Draw complete free body...
solve them clear please with formeula & FBD The collar at O and attached shaft OC rotate about the fixed X-axis at a constant rate 1 = 4 rad/s. The circular disk with radius 300 mm rotates at an angular velocity of ) = 10 rad/s and accelerates at a rate of Ö = 2 rad/s2. An observer and xyz coordinate system are attached to the disk, as shown in the figure below The following equations are to be used...