Rod ABC is made of a steel for which the yield strength is oy= 450 MPa...
100 KN 150 mm 450 mm ΑΙ B G С The three cylinder rods made of A-36 steel and have equal cross-sectional areas support a vertical load of 100kN as shown. The bar ABC is fully rigid. Determine: a) The force at A, B and C. b) The diameter of the rods consider safety factor of 1.5, rounded to the nearest even number. c) The displacement of point A, B, C. A 36 steel, Modulus of elasticity E = 200...
[20 pts] A cable is made of 1040 steel which has 400 MPa yield strength and 500 MPa tensile strength. Calculate the minimum diameter required for such cable that carries a 250 kg elevator with 6 people in it without any permanent deformation to the cable. Assume a design/safety factor of 2.5. Assume the average weight of a single person as 80 kg. Gravitational acceleration: 9.81 m/s2 Lutfen birini seçin: O a. 3.38 mm O b. 3.77 mm O C....
For a certain steel alloy, the yield strength is 560 MPa and the Young’s modulus is 200 GPa. What is the maximum load that may be applied to a specimen with a cross sectional area of without plastic deformation?
a cylindrical tank is made from A-36 OBLEM 2: The cylindrical tank is made from A-36 steel with a yield strength ayie 250 MPa, modulus ef elasticity &-200 GPa and Poisson's ratio v 0.3. When the tank is pressuri pressure p, a 60 strain rosette mounted on the surface measures the following strains: & 100(10), 343(10), maximum-distortion-energy theory, to determine the factor of safety against yielding (c) Find the internal pressure p acting within the tank. (30 Points) 343(10) Use...
ViewHelp Review .E. A A. Search ROD AaBbc Aabe ODE ABAC AaBbc O CH RODARICA Emphasing Thing? S S T The Spar Sutte. Des u A E - QUESTION 2 A. The table below lists the Young's modulus €, the yield strength (Oy), ultimate tensile strength (.) and ductile (Er) for there materials. (% Material Brass Copper Steel E (GPa) 100 110 207 Oy (MPa) 345 250 450 (MPa) 420 290 550 Calculate the modulus of resilience and the toughness...
2. The rod is made of a material having a yield stress oy = 250 MPa. Determine the minimum required diameter for its sections take at segments AB and BC. Apply a factor of safety F.S. = 1.5 against yielding. 600 mm mm 1 ZA 40 KN 50 KN
A thin-walled pipe of 10 cm diameter is used to carry hot steam at a pressure of 2.5 MPa. The pipe is made with a steel with Young's modulus of 200 GPa, yield strength of 1000 MPa and fracture toughness (KIe) of 2.85x107 Nm32. Determine the minimum thickness of the pipe using the leak-before-break criterion assuming a semi-circular shape of the cracks in the vessel wall and a safety factor of 9. (b) 17 marks] A thin-walled pipe of 10...
A composite rod is made up of typical structural steel (on the inside) and high strength steel (on the outside). Both steels (in fact all steels) have the same elastic shear modulus G- 80 GPa. The normal steel (inside) has a shear yield stress of 240 MPa. The high strength steel (outside) has a shear yield stress of 480 MPa. The rod is torqued so that the perimeter reaches a shear strain of 0.006. (a) Draw the strain diagram. (b...
o (MPa) 750 If the yield strength of aluminium alloy (450 MPa) that is used for making aircraft parts increases to 600 MPa after strain hardening, find B F 600 ofy = 450 parallel 300 150 a) the Elastic modulus and b) the modulus of resilience both before and after strain hardening. 0 C D € (mm/mm) 0.01 0.02 0.03 0.04 0.006 0.023 COC y Eoc=plastic strain
(b) A thin-walled pipe of 10 cm diameter is used to carry hot steam at a pressure of 2.5 MPa. The pipe is made with a steel with Young's modulus of 200 GPa, yield strength of 1000 MPa and fracture toughness (Kic) of 2.85x10 Nm32. Determine the minimum thickness of the pipe using the leak-before-break criterion assuming a semi-circular shape of the cracks in the vessel wall and a safety factor of 9. [7 marks] (b) A thin-walled pipe of...