12.34 The parameter values for the circuit in Fig, P1227 PSPICE are as follows: R =...
13.20 There is no energy stored in the circuit in Fig. P13.20 at the time the voltage source is turned on, and 325u(t) V PSPICE MULTISIM a) Find Vo and Io b) Find vo and i c) Do the solutions for v, and i, make sense in terms of known circuit behavior? Explain Figure P13.20 800 nF 250 250 43625 625 mH 500
MULTISIM 10.65 The variable load resistor R¡ in the circuit shown in PSPICE Fig. P10.65 is adjusted for maximum average power transfer to RL a) Find the maximum average power. b) What percentage of the average power devel- oped by the ideal voltage source is delivered to Rź when R is absorbing maximum average power? c) Test your solution by showing that the power developed by the ideal voltage source equals the power dissipated in the circuit. Figure P10.65 1212...
7.14 The switch in the circuit in Fig. P7.14 has been PSPICE closed for a long time before opening a ULMvot) fort0. t t 0. Find Figure P7.14 2.5 vo 320 mH 60 V
7.36 The switch in the circuit shown in Fig. P7.36 has PSPICE been in position a for a long time. At t=0, the MULTISIM switch moves instantaneously to position b. a) Find the numerical expression for it) when 120. b) Find the numerical expression for v.) for t2 01. Figure P7.36 1=0 ь 102 312002 50A 380 V.3 402 40 mH 800 V
Find closed loop gain and i0
he circuit 8.28. For Fig. 8.58, using ideal op-amp model, cal- at choice Vinl to culate the closed-loop gain . Also find io when us 1.2V. 12 0 V2 + io 20 kQ + 2.5 k2 Vo 10 k Figure 8.58
he circuit 8.28. For Fig. 8.58, using ideal op-amp model, cal- at choice Vinl to culate the closed-loop gain . Also find io when us 1.2V. 12 0 V2 + io 20 kQ...
ㄥ FIGURE 9.39 The circuit shown schematically in Fig. 9.39 is constructed using R- 20 m2 C= 50 mf, and L = 2 ml. (a) Find an expression for 4r(1) valid for 1 > 0 if v(O+) = 0 and i (0° ) = 2 mA. (b) Sketch your solution over the range of <t< 500 ms. (c) Simulate the circuit using PSpice. Submit a properly labeled schematic with your plot. Does the simulation agree with your analytical result? (Don't...
solve for part a & b only
13.46 PSPICE MULTISIM The op amp in the circuit shown in Fig. P13.460 is ideal. There is no energy stored in the circuit at the time it is energized. If v, = 20,000tu(t)V, find (a) V., (b) v,, (c) how long it takes to saturate the operational amplifier, and (d) how small the rate of increase in v, must be to prevent saturation. Figure P13.46 100 nF HE C2 1 k12 R2 5V...
PLEASE SHOW ALL WORK AND TO FOLLOW ALL DIRECTIONS. PLEASE USE
PSPICE.
Assignment 1. Using a DC Sweep analysis to analyze a circuit: Use the circuit below. A. Analyze the circuit by hand (find Va and is only). B. Analyze the circuit using PSPICE as follows: Use a DC Sweep analysis to find the quantities found in part A above. Include a voltage printer and a current printer to measure the quantities specified. Do not use a Bias Point analysis...
= For the circuit of Fig. 8.27, let io(t < 0) = -1 mA, 1,(t > 0) = 2 mA, R 2.000 Q, R = 3,000 12, and L = 20 mH. a. Find va for t > 0. b. What is the approximate duration of the transient? 6. Sketch va(t). FIGURE 8.27
2. Use PSpice to find Io and Vo in the circuit below. 50 nF 10mH 20Ω 1()cos(10t) v 2052 Figure 2 Let v1-o, v1-5, TD-0, TR-u,F-u, P-2.Sm, and PER-Sm