Q1: For ideal transformers, can you explain the ratio between windings, current, and voltage. And explain the relationships of the ratios when the circuit is referred to primary and secondary. Show the proof.
Q2: Using the ideal transformer ratio, how do we find its referred( primary or secondary) impedance.
Q3: Show the proof for reactance and resistance when
referred to primary or secondary. Hint : R= a^2 * R , R/a^2
How do we know when to use these formulas?
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Q1: For ideal transformers, can you explain the ratio between windings, current, and voltage. And explain...
a) Transformers work by the Principle of Electromagnetic Induction. Briefly explain this to a layman. b) i. [2 marks] [1 mark] State the two (2) types of losses in a transformer and also state where in the [2 marks] State two (2) advantages of an auto-transformer over an ordinary [2 marks] State why DC voltages do not work in transformers. 11. transformer these losses can be found. 111. transformer. c) Explain briefly why electric power is transmitted at very high...
Learning Goal: To understand the concepts explaining the operation of transformers.One of the advantages of alternating current (ac) over direct current (dc) is the ease with which voltage levels can be increased or decreased. Such a need is alwayspresent due to the practical requirements of energy distribution. On the one hand, the voltage supplied to the end users must be reasonably low for safety reasons(depending on the country, that voltage may be 110 volts, 220 volts, or some other value...
Please answer this question Q3. The power rating and the voltage ratio of the power transformer and the CT ratio are show in Fig 3. Determine the transformation turns ratios and the connection of the interposing transformers required in order to set the differential relays, which are provided with taps. Draw the complete three- phase connection schematic diagram and identify the currents in each of the elements. 150/ 5Y 115 Transformer Vector group: Primary secondary: Yd5 Primary.tertiary YO 1151V2SMVA13V SMVA...
1. In order to meet an emergency, three single-phase transformers with 12.470/7.200 V are connected in Delta-Wye to form a three-phase transformer which is fed by a 12.470 V transmission line. If the transformer supplies 60 MVA to a load, calculate: (3 marks) a. The turns ratio for each transformer b. The currents in the primary and secondary windings of the transformer c. The primary and secondary transmission line currents 2. A Wye-Delta transformer is connected to a 66 kV...
A three-phase Yy0 connected transformer has a nominal rating of 250 kVA and a voltage ratio 15:0.4 kV. After conducting the short-circuit test, where the secondary winding is short-circuited, it is found that the primary series resistance is 0.08 pu and the primary series impedance magnitude is 0.1pu. The effect of the parallel branch in the transformer’s equivalent circuit may be neglected. Explain what information ‘Yy0’ gives about the transformer. Draw the per-phase equivalent circuit of the transformer during the...
The Lights Q1. Our LED lights are to be powered from a 12 V DC source. Assuming ideal diode characteristics in the rectifier we use and no voltage drops along the wires, what turns ratio N1:N2 is required for a transformer for the lighting subsystem (assume a UK mains system)? The turns ratio required is ? ( 1:20 / 1:10 /20:1 /10:1) [1 mark] Q2. If we have 1000 parking spaces, we have 1000 lights each drawing 20 mA switched...
PLEASE SO PART C, THANK YOU WILL RATE. A single-phase transformer with a 5:1 turns ratio is connected to a 600 V voltage source on the primary side, and a 5 Ω resistor on the secondary. A current of 22 amps of current is measured to flow through the 5 Ω resistor on the secondary side. The real power flowing into the transformer primary is measured at 2500 W. You can neglect Lm and Rc (the magnetizing inductance and core...
For an ideal transformer, what is the ratio in terms of winding, current, and voltage? Explain how you derive it and what is Zp = a^2 * Z_L ? Why is it a^2 and not just a?
Q1) Two ideal voltage sources designated as machines 1 and 2 are connected as shown in Figure 1. If E! = 100.200 V, E-100し300 V and Z = 0 +JS a) Determine whether each machine is generating or consuming real power and the amount b) Determine whether each machine is receiving or supplying reactive power and the amount c) Determine the P and Q absorbed by the impedance 2 #2 Figure 1: Ideal voltage sources connected through impedance Z Q2)...
solve no: 3.14 , 3.16, 3.19 please show each step and solve for beginners 120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...