A 2.15 Vrms signal is measured across a 600 ohm load. Convert this measured value to its dbm (600) equivalent
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
A 2.15 Vrms signal is measured across a 600 ohm load. Convert this measured value to...
A 67 Vrms source is placed across a load that consists of a 12 ohm resistor in series with an capacitor whose reactance is 5 ohms. Compute the following: a) The average power of the load b) The reactive power of the load c) The apparent power of the load d) The power factor of the load
Removing the 2 ohm load resistor and looking into the terminals where Vo is measured, what is the Thevenin equivalent impedance of the circuit in rectangular coordinates Look at the circuit below j312 - 3412 Ro = 22 VO 420° A 620° V + + 412
A 600 VA, 60 Hz, 220/12 Vrms transformer is connected as an autotransformer. Assuming the transformer is ideal, determine a) the output voltage, b) the maximum V-A load rating possible, c) and the maximum input current, d) Determine the input current if a 50 Ohm resistor is connected on the output with 220 V applied to the primary.
a load impedance described by 20+J12 ohm has 500Vrms applied across the load impedance. 1) draw the circuit with resistor, inductor and capacitor components that has this load impedance with frequency of 100 Hz. 2) if the load is in a 3 phase power Y-Y configuration with line impedance of 1 ohm, determine: a) the line voltage at the load b) the phase voltage at the source
A load impedance consists of 25 ohm resistance in series with 38 ohm inductive reactance. The load is connected across a 60 Hz, 240 V rms source. Use the voltage source as the reference (zero phase angle). a. Draw the circuit diagram. b. Calculate the value of inductance. c. Calculate the phasor value of current through the load impedance. d. Which leads, current or voltage? e. What is the phase angle between current and voltage? d. Calculate the phasor value...
Please answer all parts. Thank you! (25 points) A half wavelength long 50 Ohm transmission line is terminated with a load of 100 Ohm. The voltage across the load is 16V 2. Determine standing wave ratio on the transmission line. Determine the incident voltage and reflected voltage at the load. Determine the incident current and reflected current a quarter wavelength away from the load. Determine the wave impedance a quarter wavelength away from the load. Design a matching network to...
(a) For Vine 220 Vrms., determine the average value of the voltage delivered to the load by using a SCR with a firing angle of 100°. Also calculate the rms value of the voltage delivered to the load by using a Triac with a firing angle of 100° (b) What is the purpose of the resistor in thyristor's snubbing circuit? What would be the effect if the resistor in the snubbing circuit is an open circuit? Find: Δ.pp L, lpL,...
two loads are connected in parralel acrros a 100 Vrms, 60Hz source. one load absorbs 500kwat 0.6pf log, the secound load absorbs 400kw and 600 kvar. determine the value of the capacitor that should be added in parralel with the 2 losds to improve the overall pf to 0.9 log
A 50-Ohm lossless air-spaced transmission line is terminated in a load. The voltage standing wave pattern on the line is measured and the resulting curve is presented in the figure. V[V] -1 -0.8 -0.6 -0.4 -0.2 0 - [m] (a) Determine the signal frequency. (b) Find the percentage of the incident power that is delivered to the load.
Two terminals a and b are attached to an unknown circuit. when a 20 ohm resistor is connected between a and b, V=15 V across the resistor. When 20 ohm resistor is removed and a 40 ohm resistor is attached between 2 terminals, V=24 across the resistor. What is thevenin equivalent circuit at terminals a and b for unknown circuit? What is max power the circuit can deliver to a load resistor and what is the value of the load...