Water is pumped from a reservoir to another reservoir whose surface elevations are 1366 feet and...
Water is pumped from a reservoir to another reservoir whose
surface elevations are 1366 feet and 1657 feet, respectively. The
connecting pipeline is 4 miles long and 10 inches in diameter. If
the pressure during pumping is 65 psi at midlength of the pipe at
elevation 1511.5 feet, what is the power? Assume the coefficient of
friction is 0.02.
Homework Answers
Add Answer to:
Water is pumped from a reservoir to another reservoir whose
surface elevations are 1366 feet and...
Water is pumped from reservoir A to B. The water-surface elevations in the reservoirs A and...
Water is pumped from reservoir A to B. The water-surface elevations in the reservoirs A and B WCalier enange is 4.1 kPa. 7.11 and 318 m, respectively. The suction line is 9.5 cm, which is short enough that the are 300 m head losses may be neglected. The pressure pipe is 400 m long and 79 cm in diameter. There are three 90° and two 45° bends. Calculate the annual power bill for pumping 0.30 m?/s. Unit power cost is...
A pipeline transfers water from Reservoir A to Reservoir B. The difference in water-surface elevations between...
A pipeline transfers water from Reservoir A to Reservoir B.
The difference in water-surface elevations between the two
reservoirs is 20 m.
The lengths of pipes 1, 2 and 3 are 1500 m, 2000 m, and 2800 m,
respectively.
The diameter of pipe 1 is 200 mm,
The diameter of pipe 2 is 500 mm, and The diameter of pipe pipe
3 is 250 mm.
The Darcy Weisbach friction coefficient of these pipes is
0.0045.
Minor loss coefficients for pipe...
NO QUESTIONS DURING T Water is to be pumped from a reservoir (ZA30 /s- to another reservoir at a higher elevati rate...
NO QUESTIONS DURING T Water is to be pumped from a reservoir (ZA30 /s- to another reservoir at a higher elevati rate of elevation (Zn THE EXAM! n) through a long pipe, as shown in the figure at a volume ow olume flow rate has been calculated and is 11 m he head loss in the pipe at this usefuf pump ) Demostrate that wh en a pump moves a fluid from one reservoir to ano e elevation difference between...
11. Water is pumped from a reservoir at a lower elevation to an elevated reservoir by...
11. Water is pumped from a reservoir at a lower elevation to an elevated reservoir by using a suitable pump. The lower reservoir water level have an atmospheric pressure head of I and is at an elevation of 20 ft. while the intake/suction side of the pump is at an elevation of 25 ft. The water is pumped at a rate of 425 gpm in a 6" diameter pipe, friction factor () is 0.017 and the length of pipe is...
Problem 3 A pipeline delivers water from Reservoir 1 to Reservoir 2 as shown in the following figure. The water levels at Reservoirs 1 and 2 are 50 ft and 20 ft, respectively. A globe valve is in...
Problem 3 A pipeline delivers water from Reservoir 1 to Reservoir 2 as shown in the following figure. The water levels at Reservoirs 1 and 2 are 50 ft and 20 ft, respectively. A globe valve is installed in the pipeline with a minor head loss coefficient k 10. The pipe from Reservoir 1 to the globe valve is 1000 ft long and 6 inches in diameter. The pipe from the globe valve to Reservoir 2 is also 1000 ft...
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through...
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter of the pipe is equal to 30 cm. Water is to be pumped by a 72% efficient motor-pump combination that draws 33 A of...
fluid mechanics SECTION A Petroleum distilate is pumped from one large diameter tank to another higher...
fluid mechanics
SECTION A Petroleum distilate is pumped from one large diameter tank to another higher tank, via a pumping station in an oil refinery. The petroleum is pumped at a speed of 2 ms through a 150 m long pipeline of 100 mm internal diameter. The vertical distance pumped is 20 m. The sum of the entry, exit and other component losses is equivalent to 5 times the velocity head, Table Q1 Fluid density Friction factor f for the...
Q4. A pump draws water from a large reservoir and delivers it to another reservoir whose water surface is 10 m higher than the pump centreline and that the pump is 1.5 meter above the suction reservo...
Q4. A pump draws water from a large reservoir and delivers it to another reservoir whose water surface is 10 m higher than the pump centreline and that the pump is 1.5 meter above the suction reservoir. The total suction and deliver pipe used is 21.1 m in length, 9 cm in diameter and has a Darcy friction factor f0.0339. The pump operates at 750 rpm and its characteristic performances are given in table below: Q (m3 s H (m)15...
Q5. A pump is located 2 m below the water surface in a reservoir as shown....
Q5. A pump is located 2 m below the water surface in a reservoir as shown. The piping between the pump and the reservoir consists of 3 m of 150-mm-diameter ductile iron pipe of 0.2 friction Coefficient. The valves and bends between the source reservoir and the pump are estimated to have a total local loss coefficient of k=50 (hikV2/2g). The water in the reservoir has a temperature of 25°C and the atmospheric pressure is 101.3 kPa. What is the...
Problem 1: In the reservoir-pipe system below, water is supplied from reservoir A to reservoir B...
Problem 1: In the reservoir-pipe system below, water is supplied from reservoir A to reservoir B with a flowrate of 50 L/S. In the system, a pump with an efficiency value of n=0.70 is used. Length of the pipeline is L=5000m, pipe diameter is D=200 mm and the elevation difference between reservoirs is 40 m. According to this, a) Determine the required pump head (Hp). b) Find the required nominal pump power. c) Draw the relative energy grade line of...
Water is pumped from reservoir A to B. The water-surface elevations in the reservoirs A and B WCalier enange is 4.1 kPa. 7.11 and 318 m, respectively. The suction line is 9.5 cm, which is short enough that the are 300 m head losses may be neglected. The pressure pipe is 400 m long and 79 cm in diameter. There are three 90° and two 45° bends. Calculate the annual power bill for pumping 0.30 m?/s. Unit power cost is...
A pipeline transfers water from Reservoir A to Reservoir B.
The difference in water-surface elevations between the two
reservoirs is 20 m.
The lengths of pipes 1, 2 and 3 are 1500 m, 2000 m, and 2800 m,
respectively.
The diameter of pipe 1 is 200 mm,
The diameter of pipe 2 is 500 mm, and The diameter of pipe pipe
3 is 250 mm.
The Darcy Weisbach friction coefficient of these pipes is
0.0045.
Minor loss coefficients for pipe...
NO QUESTIONS DURING T Water is to be pumped from a reservoir (ZA30 /s- to another reservoir at a higher elevati rate of elevation (Zn THE EXAM! n) through a long pipe, as shown in the figure at a volume ow olume flow rate has been calculated and is 11 m he head loss in the pipe at this usefuf pump ) Demostrate that wh en a pump moves a fluid from one reservoir to ano e elevation difference between...
11. Water is pumped from a reservoir at a lower elevation to an elevated reservoir by using a suitable pump. The lower reservoir water level have an atmospheric pressure head of I and is at an elevation of 20 ft. while the intake/suction side of the pump is at an elevation of 25 ft. The water is pumped at a rate of 425 gpm in a 6" diameter pipe, friction factor () is 0.017 and the length of pipe is...
Problem 3 A pipeline delivers water from Reservoir 1 to Reservoir 2 as shown in the following figure. The water levels at Reservoirs 1 and 2 are 50 ft and 20 ft, respectively. A globe valve is installed in the pipeline with a minor head loss coefficient k 10. The pipe from Reservoir 1 to the globe valve is 1000 ft long and 6 inches in diameter. The pipe from the globe valve to Reservoir 2 is also 1000 ft...
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter of the pipe is equal to 30 cm. Water is to be pumped by a 72% efficient motor-pump combination that draws 33 A of...
fluid mechanics
SECTION A Petroleum distilate is pumped from one large diameter tank to another higher tank, via a pumping station in an oil refinery. The petroleum is pumped at a speed of 2 ms through a 150 m long pipeline of 100 mm internal diameter. The vertical distance pumped is 20 m. The sum of the entry, exit and other component losses is equivalent to 5 times the velocity head, Table Q1 Fluid density Friction factor f for the...
Q4. A pump draws water from a large reservoir and delivers it to another reservoir whose water surface is 10 m higher than the pump centreline and that the pump is 1.5 meter above the suction reservoir. The total suction and deliver pipe used is 21.1 m in length, 9 cm in diameter and has a Darcy friction factor f0.0339. The pump operates at 750 rpm and its characteristic performances are given in table below: Q (m3 s H (m)15...
Q5. A pump is located 2 m below the water surface in a reservoir as shown. The piping between the pump and the reservoir consists of 3 m of 150-mm-diameter ductile iron pipe of 0.2 friction Coefficient. The valves and bends between the source reservoir and the pump are estimated to have a total local loss coefficient of k=50 (hikV2/2g). The water in the reservoir has a temperature of 25°C and the atmospheric pressure is 101.3 kPa. What is the...
Problem 1: In the reservoir-pipe system below, water is supplied from reservoir A to reservoir B with a flowrate of 50 L/S. In the system, a pump with an efficiency value of n=0.70 is used. Length of the pipeline is L=5000m, pipe diameter is D=200 mm and the elevation difference between reservoirs is 40 m. According to this, a) Determine the required pump head (Hp). b) Find the required nominal pump power. c) Draw the relative energy grade line of...
Most questions answered within 3 hours.
-
What is the % w/v when 80 mL of a 2.0% solution is mixed with 50...
asked 3 minutes ago -
How can I solve the following using a TI83
Claim: Most adults would erase all of...
asked 15 minutes ago -
Analysis of 3-ethyl-3-buten-2-ol gave C, 72.13%; H, 11.92%.
Calculate the percent deviation of these results from...
asked 12 minutes ago -
Which VALS segment is most likely to have a top of the line
brand new (2015)...
asked 16 minutes ago -
Write a program to score the paper-rock-scissor game. Each of
two users types in either P,R...
asked 36 minutes ago -
Calculate the equillibrium constent K for a redox reaction that
has E°cell = -.98 V at...
asked 48 minutes ago -
A concave spherical mirror has a radius of curvature of
magnitude 19.6 cm.
(a) Find the...
asked 50 minutes ago -
3. draw a diagram of the magnetic field:
a. around a long straight wire with a...
asked 49 minutes ago -
If you titrated 30.0 mL of 0.1 M HCl with 0.1 M NaOH, indicate
the approximate...
asked 57 minutes ago -
NADH passes electrons into the electron transport chain. List
the carriers that would receive the electrons,...
asked 1 hour ago -
A cylindrical cable with a resistivity of 1.6x10-8 Ω·m and cross
sectional area of 3x10-5 m^2...
asked 1 hour ago -
True or False.
A consumer with convex preferences who is indifferent between
the bundles (5,2) and...
asked 1 hour ago