I need a Matlab code for a 4-bit parallel in serial out shift register.
Hardware Requirements:
Arduino board
Four push buttons
74HC165 8-bit parallel-in-serial-out shift register
Four 10K ohm resistors
Hardware Setup:
Connect push buttons and 74HC165 shift registers to Arduino
hardware:
Connect Vcc pin on 74HC165 to 5V pin on Arduino hardware.
Connect GND pin on 74HC165 to GND pin on Arduino hardware.
Connect Q7 pin on 74HC165 to digital pin 11 on Arduino hardware.
Connect CP pin on 74HC165 to digital pin 8 on Arduino hardware.
Connect PL pin on 74HC165 to digital pin 9 on Arduino hardware.
Connect CE pin on 74HC165 to digital pin 10 on Arduino hardware.
Connect a push button to pin D0, D4, D5 and D7 on 74HC165 with a pull down resistor to GND as shown below.
Connect pin D1, D2, D3 and D6 on 74HC165 to GND pin on Arduino hardware
%Create an arduino object, and include the ShiftRegister library
a = arduino('COM4','Uno','Libraries','ShiftRegister')
% define datapin and clockpin and loadpin
dataPin = 'D11';
clockPin = 'D8';
loadPin = 'D9';
clockEnablePin = 'D10';
register =
shiftRegister(a,'74HC165',dataPin,clockPin,loadPin,clockEnablePin)
%read pushbutton states
states = read(register, 8);
pressedButtons = find(states == 1)-1;
if ~isempty(pressedButtons)
bitsStr = num2str(pressedButtons, '%d ');
disp(['Push button(s) connected to bit ', bitsStr, ' is
pressed']);
end
%When the connection is no longer needed, clear the shift register and arduino object.
clear register a
I need a Matlab code for a 4-bit parallel in serial out shift register.
Computer archetecture. Build an 8-bit SIPO (serial-in, parallel-out) shift register in diagram, need to have D flip-flop. The goal is to use a button , led light, and SIPO register to make an interactive light show.
2. A 4-bit parallel in/serial out shift register has SHIFT/LOAD' and CLK inputs as shown in the figure below. What is the output Q3 at the two times('A' followed by 'B') indicated by the dashed lines in the figure below if the parallel data inputs are DO-1, D1-0, D2-1, and D3-1? D3 SHIFT/L CLK SHIFT /LOAD Ο A. A-0,9:0 B. A:0, B-1 D.A-1, B-1
Exercise 3. [10 Marks Draw a 4-bit Serial In, Serial Out register using SR flip-flops. For example, the below diagram represents a Parallel In, Parallel Out n-bit register using ID flip-flops. dn-i dn-i do CLK
4 C) Draw the waveforms for the serial in/ parallel out shift register CLA 2i o. Data in CLK 20 ei 2. 2a
With a 7494 parallel in serial out shift register, when you have 1101 loaded in the register what happens when you set the serial input to low and pulse the clock input 6 times? set to high and pulse 6 times?
Using D FFs and selectors, design a 4-bit shift register (SR) (with only serial inputs) that can shift its content one or two bits to the left or right.
5) The content of a 4-bit shift register is initially 1101. The register is shifted six times to the right, with the serial input being 101101. What are the contents of the register after each shift?
Shift Register: Design a 4-bit shift register for the following function table. Inputs are D3D2D1D0 for parallel data load, S1S0 are the mode control, and the clock. Outputs are the register bits Q3Q2Q1Q0. Show the complete logic diagram.
I want matlab code to plot 8-bit FSK ( frequency shift modulation ) for bit error rate
Question #5 (3 marks): The content of a 4-bit register is initially 1001. The register is shifted six times to the right, with the serial input (SI) being 010010. What is the content of the register after each shift? --------- --------- Serial in (SI) Serial in (SI) NO D1Q1 - D 2 Q2 Io D3 03 _ Dr D3 Q3 DO QO Serial out (SO) CE CE HCE LACE 1 Shift Clock - Q3 Q2 Q1 QO 1 0 0...