Draw in the required position of the DMM selector switch for testing a Hall effect sensor....
Draw in the required position of the DMM selector switch for testing a Hall effect sensor. Connect the DMM test lead to the meter. Connect the test leads to the correct pins to measure the output (+) of the Hall effect sensor.
Homework Answers
Typical Hall effect sensor has three pin as shown below
Vcc and Gnd pin are used to give power to sensor. OUT pin gives high or low voltage depending on the magnetic field.
DMM switch should be at Voltage measurement to measure the ouput voltage of hall sensor. Red probe of DMM should be connected to OUT pin and black probe of DMM should be connected to GND pin of Hall sensor.
Please thumbs up
Add Answer to:
Draw in the required position of the DMM selector
switch for testing a Hall effect sensor....
4) A paddle wheel flow sensor that uses hall-effect sensors is used to measure the flow of a flui...
4) A paddle wheel flow sensor that uses hall-effect sensors is used to measure the flow of a fluid and shown in Figure 3. The CPR of the hall-effect sensor is 16 however the maximum flow rate resolution should be 512 pulses. The maximum rate of flow relates to 4 rounds per second of the paddle wheel. The output from the hall-effect sensor is a 5O% square wave -sv to +SV. Develop a design (mechanical and electrical) that provides a...
Identify the element which makes the following scenario INCORRECT 11. An electrician is testing a switch using a mul...
Identify the element which makes the following scenario INCORRECT 11. An electrician is testing a switch using a multimeter as an ohmmeter. The the is not installed. First, the electrician connects the two leads of the meter to two terminals of the switch where the power conductors would be con nected it the switch were installed. The switch is in the OFF position, and the meter shows maximum resistance. Then, the electrician opens the switch to the ON position, and...
There will be a flow from the battery when the switch is open and, for the sake of discussion, we...
need help to do the pressure and flow parts, heres a pic of the
circuit
There will be a flow from the battery when the switch is open and, for the sake of discussion, we'1 call that flow I glow. Assume that the obstacle presented by any of the identical bulbs is L no matter what flow goes through it. (This is equivalent to; assume that the bulbs are ideal') Copy the following table into your pre-lab Table 6; Pressure...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 an...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
Principles of Inorganic Chemistry! Week 5 Effect of Temperature on Solubility of a Salt In this experiment, you w...
Principles of Inorganic Chemistry! Week 5 Effect of Temperature on Solubility of a Salt In this experiment, you will study the effect of changing temperature on the amount of solute that will dissolve in a given amount of water. Water solubility is an important physical property in chemistry, and is often expressed as the mass of solute that dissolves in 100 g of water at a certain temperature. In this experiment, you will completely dissolve different quantities of potassium nitrate,...
Prelab Activity: Electrochemical Cells To determine the solubility product of copper(II) carbonate, CuCO3 , a concentration...
Prelab Activity:
Electrochemical Cells
To determine the solubility product of copper(II) carbonate,
CuCO3 , a concentration cell as described on pages 71-72
of the lab handout is constructed. The temperature of the Galvanic
cell is measured to be 22.5°C, and the cell potential 282 mV (0.282
V). Using this data and Equation 8 in the lab manual, calculate the
Ksp for CuCO3 and report your answer with
three significant digits.
For the Galvanic cell you will construct in PART B,...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
summarizr the followung info and write them in your own words and break them into different...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...
1. According to the paper, what does lactate dehydrogenase (LDH) do and what does it allow...
1. According to the paper, what does lactate dehydrogenase
(LDH) do and what does it allow to happen within the myofiber? (5
points)
2. According to the paper, what is the major disadvantage of
relying on glycolysis during high-intensity exercise? (5
points)
3. Using Figure 1 in the paper, briefly describe the different
sources of ATP production at 50% versus 90% AND explain whether you
believe this depiction of ATP production applies to a Type IIX
myofiber in a human....
4) A paddle wheel flow sensor that uses hall-effect sensors is used to measure the flow of a fluid and shown in Figure 3. The CPR of the hall-effect sensor is 16 however the maximum flow rate resolution should be 512 pulses. The maximum rate of flow relates to 4 rounds per second of the paddle wheel. The output from the hall-effect sensor is a 5O% square wave -sv to +SV. Develop a design (mechanical and electrical) that provides a...
Identify the element which makes the following scenario INCORRECT 11. An electrician is testing a switch using a multimeter as an ohmmeter. The the is not installed. First, the electrician connects the two leads of the meter to two terminals of the switch where the power conductors would be con nected it the switch were installed. The switch is in the OFF position, and the meter shows maximum resistance. Then, the electrician opens the switch to the ON position, and...
need help to do the pressure and flow parts, heres a pic of the
circuit
There will be a flow from the battery when the switch is open and, for the sake of discussion, we'1 call that flow I glow. Assume that the obstacle presented by any of the identical bulbs is L no matter what flow goes through it. (This is equivalent to; assume that the bulbs are ideal') Copy the following table into your pre-lab Table 6; Pressure...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
Principles of Inorganic Chemistry! Week 5 Effect of Temperature on Solubility of a Salt In this experiment, you will study the effect of changing temperature on the amount of solute that will dissolve in a given amount of water. Water solubility is an important physical property in chemistry, and is often expressed as the mass of solute that dissolves in 100 g of water at a certain temperature. In this experiment, you will completely dissolve different quantities of potassium nitrate,...
Prelab Activity:
Electrochemical Cells
To determine the solubility product of copper(II) carbonate,
CuCO3 , a concentration cell as described on pages 71-72
of the lab handout is constructed. The temperature of the Galvanic
cell is measured to be 22.5°C, and the cell potential 282 mV (0.282
V). Using this data and Equation 8 in the lab manual, calculate the
Ksp for CuCO3 and report your answer with
three significant digits.
For the Galvanic cell you will construct in PART B,...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
1. According to the paper, what does lactate dehydrogenase
(LDH) do and what does it allow to happen within the myofiber? (5
points)
2. According to the paper, what is the major disadvantage of
relying on glycolysis during high-intensity exercise? (5
points)
3. Using Figure 1 in the paper, briefly describe the different
sources of ATP production at 50% versus 90% AND explain whether you
believe this depiction of ATP production applies to a Type IIX
myofiber in a human....
Most questions answered within 3 hours.
-
What is the discount rate for the following cash flows? (Please
show your calculation procedure)
Year...
asked 11 minutes ago -
Let X be the amount of damage a particular company pays out (in
$) for a...
asked 1 hour ago -
1. Choose the answer that is closest to the definition of a
significance level
a) If...
asked 2 hours ago -
When light is refracted, on what does the angle of refraction
depend? Select all that apply....
asked 2 hours ago -
A (726) g mass is hung on a spring. As a result the spring
stretches (16.5)...
asked 3 hours ago -
SOLUTION NOT NEEDED ONLY NEED THE ANSWERS, HOMEWORK IS DUE IN 30
MINUTES.
4)Which of the...
asked 3 hours ago -
You will select one card from a standard deck of 52 cards. What
is the probability...
asked 4 hours ago -
50% of the volume of a boat, sailing down the Mississippi (where
the water density ρ...
asked 4 hours ago -
Calculate how many moles of ions are in 1.4 L of 2.9 M KNO2
(aq). Remember...
asked 5 hours ago -
Experiment:
In the experiment: Mix together 74 g. (92 ml.) of n-butyl
alcohol and 120 g....
asked 6 hours ago -
This Python module will be menu driven
and use conditions to check user input in order...
asked 6 hours ago -
Tip Calculator App
For this project, you will create a tip calculator Android
app. The user...
asked 7 hours ago