Question

There will be a flow from the battery when the switch is open and, for the sake of discussion, we1 call that flow I glow. As


need help to do the pressure and flow parts, heres a pic of the circuit

I Multimeters Purpose .To connect flow of electricity, obstacle and pressure difference to quantities that the DMM can measur

There will be a flow from the battery when the switch is open and, for the sake of discussion, we'1 call that flow I glow. Assume that the obstacle presented by any of the identical bulbs is L no matter what flow goes through it. (This is equivalent to; assume that the bulbs are ideal') Copy the following table into your pre-lab Table 6; Pressure Difference caused by the Battery through bulb Flow Obstacle presentedFlow from to Battery (in terms Battery of I Switch open l glow Switch closed Fill out the rest of table six in your pre-lab. 17 Explain the change in brightness of bulb A when the switch closes. [11 Notice that this explanation is not possible without the knowing about pressure difference (as measured by product"). At least in this one case, the idea of "difference in pressure" shows its value in predicting brightness changes in DC circuits. Let's see if the idea helps in the context of circuit 9 (below)
I Multimeters Purpose .To connect flow of electricity, obstacle and pressure difference to quantities that the DMM can measure To introduce DMM's and use them to make measurements Equipment I multimeter with an input impedance of at least 10 M2 2 Rechargeable batteries 3 rheostats (with 30 A.W.G. Kanthal AlI) 3が48 bulbs in bulb-holders 8 alligator-to-alligator wires pair of 36" banana-to-alligator wires 2 pairs of 24" banana-to-banana leads *1 large resistor (22 M) Verify that you have all of the equipment listed. Notify your TA if anything is missing. Introduction We return to a circuit that you partly examined in the pre-lab for electricity IV. You were in a position to make predictions about the brightness of the identical bulbs in; Circuit 1 Lt느 乙 But you weren't asked to predict the effect of closing the switch on bulb A (although you built and observed the actual brightness of bulb A earlier in this lab).
0 0
Add a comment Improve this question Transcribed image text
Answer #1

I nthally uhen suntch is open ou base a r rent in cach wuib 1 5 Now posential aCaoss total 3 3 potenstal ac ossDsL+L Now Potential acooss is total 3Y 8 3 poterttal acyoss Ds B L potential across D ニpotentfala(rossa-こpotentida(oss c in pav. AGREE diteune bulb A asoss A suite h glow O u) s untch clore 3 a glow 2

Add a comment
Know the answer?
Add Answer to:
There will be a flow from the battery when the switch is open and, for the sake of discussion, we...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 1) What happens to the electrical flow going into and out of the battery if you...

    1) What happens to the electrical flow going into and out of the battery if you add more bulbs in parallel? 2) What happens to the electrical flow going into and out of the battery if you add more bulbs in series? 3) Let's say you have three bulbs (bulb 1, bulb 2 and bulb 3) in parallel and you create "short" pathway across bulb 3, what happens to the brightness of the bulbs? 4) What happens to the brightness...

  • In this set of exercises (in the pre-lab AND lab), we will test/make the following assumptions:...

    In this set of exercises (in the pre-lab AND lab), we will test/make the following assumptions: A flow exists in a complete circuit from one terminal of the battery, through the rest of the circuit, back to the other terminal of the battery, through the battery and back around i. the circuit. We will call this flow electric current For identical bulbs, bulb brightness can be used as an indicator of the amount of current through that bulb: the brighter...

  • i think you have to use excel and graph it for the last question Table 2:...

    i think you have to use excel and graph it for the last question Table 2: two D-cells in series Circuit Flow Obstacle Product for Flow Obstacle Product through Presented the through Presented for the Network by Network of the by the Rhcostat of Bulbs Network Bulbs Rhcostat Rheostat (glow-cm) (glow) of Bulbs (glow-cm) (glow) (cm) (cm) 9 1 59.3 59.3 1 2 20.8 220.8 10 2 29.7 59.3 2 110.2 220.4 3 19.8 59.3 3 70.5 211.5 11 Table...

  • Parallel Circuit Please answer the following Questions. heres the circuit .What can you infer about the...

    Parallel Circuit Please answer the following Questions. heres the circuit .What can you infer about the current through each of the bulbs as each additional bulb is added in parallel? Explain. What can you infer about the current through the battery as each additional bulb is added in parallel? Explain. . What can you infer about the current through the whole circuit as each additional bulb is added in parallel? Explain. Refer back to your rule developed in section 2...

  • (2) Five identical bulbs (numbered 1-4) are arranged as shown (a) Rank the brightness of from...

    (2) Five identical bulbs (numbered 1-4) are arranged as shown (a) Rank the brightness of from BRIGHTEST to DIMMEST (b) What would happen to the brightness of Bulb 1 if the wire was cut between bulbs 2 and 3? Explain 5 (c) You have 3 bulbs, some wire, and a battery. Draw two circuits: One circuit must have have all 3 bulbs be brighter than the ones in the other circuit (3) Find the the current and potential difference for...

  • 1. Why can the DSO only measure node voltages when the Function Generator is the power supply in ...

    1. Why can the DSO only measure node voltages when the Function Generator is the power supply in a circuit (unless it is using a current probe)? 2. Consider Figure 1. According to the calculations in the lab handout, if Z-1kΩ +/6914, then the phase difference (фи-фі) between u(t) and i (t) is 34.6". a. If this v(t) and i(t) were displayed on a DSO (v(t) being a node voltage and using a current probe for i(t) as shown in...

  • I only need help with the discussion there are many info that you do not need put I put just in ...

    I only need help with the discussion there are many info that you do not need put I put just in case as well as my data table. please do it as soon as u can Meauements ODeit1 Check2 Meaurements Checi3 Ced Check5 Check6 Measurements Check7 heck8 4058 33 536 1502 1035 979 119478 041 1.0319|0.554972| 64261| 153|15542033681 995781 5266566 1578807 298h 1631 119 1209430016 079096812 0.418135246 0,00032665 011890:004668155728441 0293237 1.291809502 1.22833 1.28 1952 -1116 4281 140616885511984206317 3346 8162 0.78...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT