Measurement And Instrumentation Theory and Application
Please answer the question below. Please show all work and write clearly . Thanks.
1. A 100Ω Platinum RTD is immersed in a liquid that is 900 C, what is the measured resistance of the RTD?
Measurement And Instrumentation Theory and Application Please answer the question below. Please show all work and...
Measurement and Instrumentation Theory and Application Please answer the below question. Please show all work and write clearly. Thanks. 7.4 A null-type Wheatstone bridge is used to accurately measure the resistance of a strain gauge during a calibration procedure. The circuit shown in Figure 7.1 is used, in which the known fixed resistance values are given by R2 =331.2 ohms and R3 =327.5 ohms. The thermometer is inserted in the circuit as Ru and then the variable resistance box Rv...
Measurement and Instrumentation Theory and Application Please answer the below question for all parts. Please show all work and write clearly. Thanks. Figure 7.9 and a hint is below. 7.23 An unknown capacitance Cu is measured using a deflection bridge as shown in Figure 7.9. The components of the bridge have the following values: Vs =10Vrms, C1 =50 uF, R2=80 ohms, R3=20 ohms. If the output voltage is 3Vrms, calculate the value of Cu. 2 Zu 3 Vs R2 0...
Please answer the question below for all parts. Please show all work and write clearly. Thanks. (You may use Excel or Matlab to make the calculations easier, but must show work and code). What is the maximum quantization error for an A/D converter with 14 bits of resolution assuming a voltage range of +/- 10 V?
Please answer the problem below for all parts . Please show all work and write clearly. Thanks.
Please answer the question below for all parts. Please show all work and write clearly. Thanks. (You may use Excel or Matlab to make the calculations easier, but must show work and code). A 1 kHz sine wave is sampled at frequency of 5 kHz. (a) What is the Nyquist frequency of the sampling system in this case? Show your work. (b) What is the Nyquist rate of the signal? Show your work. (c) Is the signal properly sampled; that...
Please answer the question below for all parts. Please show all work and write clearly. Thanks A sender needs to send out 5 numbers (3, 11, 12, 9, 7). Answer the following: Find the checksum at the sender site Find the checksum at the receiver site if there is no error Find the checksum at the receiver site if the first data is changed to 5. Find the checksum at the receiver site if the first data is changed to...
Please answer the problem below for all parts. Please show all work and write clearly. Thanks. The gain equation is then Using an AD620 Instrumentation Amplifier and the bridge shown below and the table shown below for 0 to 100°C (AD620 specifications online) 4. 49.4k2 What gain and AD620 Gain Resistor is needed to produce an output of 0 to 3.3 volts for input to the ADC of a microcontroller? Show the circuit you would use, including the connections RG...
Please show all work step by step and final answer. Electrochemical Measurement of Concentration An electrochemical cell consists of a standard hydrogen electrode and a copper metal electrode. What is the potential of this cell at 25°C if the copper electrode is placed in a solution in which [Cu2+] = 3.6x10-4 M? 1 pts Submit Answer Tries 0/5 The copper electrode of the above cell is placed in a solution of unknown [Cu2+]. The measured potential at 25°C is 0.136...
Please show all work step by step and final answer. Electrochemical Measurement of Concentration An electrochemical cell consists of a standard hydrogen electrode and a copper metal electrode. What is the potential of this cell at 25°C if the copper electrode is placed in a solution in which [Cu2+] = 3.2x10-6 M? 1 pts Submit Answer Tries 0/5 The copper electrode of the above cell is placed in a solution of unknown [Cu2+]. The measured potential at 25°C is 0.038...
measurement and instrumentation exercise plz read and answer . KES 1215 : MESUREMENT AND INSTRUMENTATION Wheatstone bridge Application: (Varley Loop Test) A Varley loop test is an application for Wheatstone bridge. The test is one of the most accurate tests of locating faults in sheathed cables or finding a short circuit in multi-core cables. It is a modification of the Murray loop test. It consists of two fixed ratio arms R1 and R2 and a rheostat R3 in the third...