Please answer the problem below for all parts. Please show all work and write clearly. Thanks.

Question

Question

The gain equation is then Using an AD620 Instrumentation Amplifier and the bridge shown below and the table shown below for 0

science Advanced-Physics

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

Ans: Given that, An AD 680 stumentotton amplitiox and the bndge Llhat 9ain ond AD0 gain esistor is needed to Produce an outpu So Ro 49.4 kJ2 L46 ь.Poe connections .Jam-lhe bidge to the AD630 S00 3 6 61

Add a comment

Answer 2

Similar Homework Help Questions

Please answer the problem below for all parts. Please show all work and write clearly. Thanks.

Please answer the problem below for all parts. Please show all work and write clearly. Thanks. The circuit below is a temperature range indicator using a Window Comparator circuit. Discuss when you would use this type of analog circuit and when you would use a microcontroller based circuit like that of Lab 4 shown below. A window comparator usually employs 2 comparators with one output indicating the input is somewhere between two limits. In these examples, a third comparator is...
Measurement and Instrumentation Theory and Application Please answer the below question. Please show all work and...

Measurement and Instrumentation Theory and Application Please answer the below question. Please show all work and write clearly. Thanks. 7.4 A null-type Wheatstone bridge is used to accurately measure the resistance of a strain gauge during a calibration procedure. The circuit shown in Figure 7.1 is used, in which the known ﬁxed resistance values are given by R2 =331.2 ohms and R3 =327.5 ohms. The thermometer is inserted in the circuit as Ru and then the variable resistance box Rv...
9. Open ended design question. There is no one right answer. Design an amplifier circuit to...

9. Open ended design question. There is no one right answer. Design an amplifier circuit to interface the thermistor half bridge shown below to the ADC in the TM4C123. Use single supply op amp techniques for your design. Show the calculations that lead to your design (Hint the concepts needed for this design were covered in lectures 15 and 16) (55 pts) 3.3 V TM4C123 S10k Your Circuit Van >10 kQ+AR Thermistor Circuit Requirements The input voltage to your circuit...

Measurement and Instrumentation Theory and Application Please answer the below question for all parts. Please show...

Measurement and Instrumentation Theory and Application Please answer the below question for all parts. Please show all work and write clearly. Thanks. Figure 7.9 and a hint is below. 7.23 An unknown capacitance Cu is measured using a deﬂection bridge as shown in Figure 7.9. The components of the bridge have the following values: Vs =10Vrms, C1 =50 uF, R2=80 ohms, R3=20 ohms. If the output voltage is 3Vrms, calculate the value of Cu. 2 Zu 3 Vs R2 0...
Please answer the problem below for all parts . Please show all work and write clearly. The answe...

Please answer the problem below for all parts . Please show all work and write clearly. The answers are below, but work must be shown to get to the answers. Thanks. answers 8.14. Design a second-order digital bandpass Chebyshev filter with the following specifications: Center frequency of 1.5 kHz Bandwidth of 200 Hz 0.5 dB passband ripple Sampling frequency of 8,000 Hz a. Determine the transfer function and difference equation. 8.14 a. 0.1815-0.1815z2 1-0.6265z +0.6370z y(n)-0.1815x(n)-0.1815x(n-2)+0.6265y(n1) 0.6370y(n-2) 8.14. Design a...
Consider the circuit shown below. Write a short analysis of whether or not it will work as designed. If you think that it won't work, discuss what changes you would make to the circuit to fi...

Consider the circuit shown below. Write a short analysis of whether or not it will work as designed. If you think that it won't work, discuss what changes you would make to the circuit to fix the problem(s). The curve of drain current versus gate to source voltage, Vos for the MOSFET is given for your reference on the next page. The maximum Drain to Source voltage of the MOSFET is 300 Volts and the maximum drain current is 5...

Problem 1) [15 marks] The gain of the dual-op-axap instrumentation amplifier shown in Fig. 1 can be adjusted by the variable resistor Ro. The op-amps are ideal. atu Fig. 1 a)Show that v.-2(1 RG )...

Problem 1) [15 marks] The gain of the dual-op-axap instrumentation amplifier shown in Fig. 1 can be adjusted by the variable resistor Ro. The op-amps are ideal. atu Fig. 1 a)Show that v.-2(1 RG )(v2-v.). b Specify suitable components to have a variable gain from 10 to 100 V/V. Problem 2) [15 marks] a) Design an op-amp limiter circuit for amplitude control with the transfer characteristic of Fig. 2(a). Use +-15V DC sources to power the circuit. Assume Vo-0.7 V...
Good morning, I need help with the following, they all relate to OP Amps. Thanks in advance. 2 value 10.00 points Problem 05.010 An op amp voltage divider Find the voltage gain vo/vs of the circ...

Good morning, I need help with the following, they all relate to OP Amps. Thanks in advance. 2 value 10.00 points Problem 05.010 An op amp voltage divider Find the voltage gain vo/vs of the circuit given below, where R1-18 kΩ and R2-14 k 2. 20 kΩ R1 1% R2 The voltage gain vo/vs of the circuit is Hints Referene eBook & Resources Hint#1 Check my work 3. 1000 points value Problem 05.025-Voltage follower Calculate the output voltage vo in...
es uestions. LEDI is Yellow and LED2 is Amber The NOR gates are 7402 with 0.35 V as typical Vou Use the circuit below to answer the and typically. Vr 1.8 V 7. 10 mA Swally. Vi Show complete work...

es uestions. LEDI is Yellow and LED2 is Amber The NOR gates are 7402 with 0.35 V as typical Vou Use the circuit below to answer the and typically. Vr 1.8 V 7. 10 mA Swally. Vi Show complete work in the space provided a. If A 1 and B 0, which LED is b. Calculate a typical value for Rg. (Round up c. If A is now 0 while B stays at 0, a (4,6, 4] on? (Round up...

Please answer the problem below for all parts . Please show all work and write clearly. Thanks.

Please answer the problem below for all parts . Please show all work and write clearly. Thanks. (a) (0) What is the difference between an autotransformer and a conventional transformer? 2. (ii) Why are high-impedance transformer used in electric toys? (b) Three single-phase transformers each rated at 150 kVA, 7200 V/600 V, 60 Hz, are connected in wye-delta on a 12470 V, 3-phase line. If the load is 450 kVA, calculate the followings: (i) The current flowing in the incoming...

Please answer the problem below for all parts. Please show all work and write clearly. Thanks.

Homework Answers