Question

What happens if you connect a DC coil of your double-pole double-throw relay to AC power...

What happens if you connect a DC coil of your double-pole double-throw relay to AC power supply with the same voltage rating?

0 0
Add a comment Improve this question Transcribed image text
Know the answer?
Add Answer to:
What happens if you connect a DC coil of your double-pole double-throw relay to AC power...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • What component in a power supply converts ac line voltage to dc voltage? What component in...

    What component in a power supply converts ac line voltage to dc voltage? What component in a power supply converts ac line voltage to dc voltage? Multiple Choice Transformer Rectifier diode O Resistor O Capacitor

  • 1) What component in a power supply converts ac line voltage to dc voltage? a. Transformer...

    1) What component in a power supply converts ac line voltage to dc voltage? a. Transformer b. rectifier diode c. resistor d. capacitor 2) A circuit that provides an entirely positive or negative output voltage when an ac input voltage is applied is called a a. rectifier b. inverter c. filter capacitor d. zener diode 3) A control voltage or current is the a. power factor b. bias c. ground d. load 4) When the voltage at the op amp's...

  • 1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliv...

    1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...

  • Styles AC Bus Local Loads T: OC Bus PV Generating DC/AC Station Zline Local Power Grid...

    Styles AC Bus Local Loads T: OC Bus PV Generating DC/AC Station Zline Local Power Grid Inverter T1 T2 Figure Q2 In the microgrid in figure Q2, a solar PV station and the local power grid supply a series of local loads The PV generating station is rated at 2 MW and is operating at unity power factor. The PV station internal impedance is purely resistive equal to 50% based on its own rating of 2 MVA. The inverter DC...

  • When you drop a magnet (North Pole first)  through a large coil and measure the induced voltage...

    When you drop a magnet (North Pole first)  through a large coil and measure the induced voltage over time, you will notice that the induced voltage has one peak upward and one peak downward. Explain why this happens. You will also notice that these voltage peaks are not the same magnitude, but the area under the peaks are nearly the same. Which peak is larger, the earlier or the later one? Explain why. What do the areas represent and why are...

  • In Lab 11 you simulated how a magnetic field can be produced by a conducting coil...

    In Lab 11 you simulated how a magnetic field can be produced by a conducting coil when powered by a DC and an AC generators. You explored the differences between the resulting magnetic fields. Consider an experimental set-up identical to what you used in the lab: a large coil connected to an AC power supply. Assume that the maximum voltage supplied by the generator stays the same but the frequency of the supplied voltage changes. As frequency changes, you measure...

  • 1. Is the power supply for a transformer AC or DC? Explain in detail why only...

    1. Is the power supply for a transformer AC or DC? Explain in detail why only this type of power supply will work. 2. Some configurations with the iron core have low efficiency while others have high efficiency. What is the iron core doing to cause this? Be specific. (Hint: think about how a transformer works.) 3. For an ideal transformer the energy must be conserved, so the average power (P=IV) in the two circuits must be equal. Therefore, if...

  • 02: Jack, a hard working ECET 201 student is building a cireuit on a boring Saturday night as described below . A DC power supply with associated grounding able to source up to 30Vc .A single pole...

    02: Jack, a hard working ECET 201 student is building a cireuit on a boring Saturday night as described below . A DC power supply with associated grounding able to source up to 30Vc .A single pole 2 state switch A resistor arrangement and a capacitor arrangement * Resistor Arrangement consists of 2-1 ΚΩ resistors in parallel with a series 500Ω resistor. Capacitor Arrangement consists 2-10μF capacitors in series with a parallel 5μ F capacitor o o ement, and capacitor...

  • a) The DC power supply below is connected to a 110 V RMS, 50 Hz AC...

    a) The DC power supply below is connected to a 110 V RMS, 50 Hz AC mains. The transformer has turns ratio N, : N2 = 10 : 1, and the diodes have forward voltage drop 0.7 V, and the regulator has dropout voltage 1.8 V. We require V 5 V. OUT =2 A GND 110 V rms O A R V Va VC 50 Hz N2 N i. Given the transformer has turns ratio Nį: N2 = 10: 1...

  • help!!!! What is the rated velocity and mechanical output power of the rotor? Velocity_1500 Power =...

    help!!!! What is the rated velocity and mechanical output power of the rotor? Velocity_1500 Power = h. r/min 186.4 3. Calculate the rotor slip velocity (in r/min) from procedures 6, 8, 9, 10 and 11. (slip velocity synchronous velocity slip (6) = slip (9) slip (11)-- rotor velocity). (5) r/min slip (8)- r/min r/min slip (10) r/min r/min 6. Couple the DC motor/generator to the wound-rotor motor with the timing belt. Turn on the power supply, Keep the variable output...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT