an aileron has a hinge moment of 900in lbs and is 9 inches long. It is...
1- A cylinder has a diameter of 12 inches, is 8 inches long, and has a 4 in ram / rod extending from one side. This is connected to a pump rated at 1.5 GPM and 1,500 PSI. What is the max load the cylinder can (push / extend)? 2- A cylinder has a diameter of 12 inches, is 8 inches long, and has a 4 in ram / rod extending from one side. This is connected to a pump...
Question 18 5p A cylinder has a diameter of 12 inches, is 8 inches long, and has a 4 in ram/rod extending from one side. This is connected to a pump rated at 1.5GPM and 1,500 PSI. What is the Horsepower rating for this system?
please use root locus graphs to find amswer. thanks The automatic control of an airplane is one example that requires multiple-variable feedback methods. In this system, the attitude of an aircraft is controlled by three sets of surfaces: elevators, a rudder, and ailerons, as shown in Figure DP7.13(a). By manipulating these surfacesi a pilot can set the aircraft on a desired flight path [20]. An autopilot, which will be considered here, is an automatic control system that controls the roll...
Problem 3 (70 pts): Consider the mechanical system in Figure , the so-called "cart pendulum" system. The cart has a moving mass M, and is connected to a linear motor via a flexible coupling with stiffness K and damping B. An inverted pendulum of length1, negligible inertia and mass m is attached to the cart via a rotary actuator. If the pendulum damping coefficient is b, the linear actuator force is F and the rotary actuator torque is t 1)...
You have 5 in diameter hydraulic cylinder 30 inches long, with a 2 in rod. What is the maximum load in lbs that can be exerted on the power stroke with a 3000 psi pump
This is the diagram that was provided. 3. It can be shown that the rotational inertia (moment of inertia) for a uniform rod about an axis that's perpendicular to the rod and passes through one of its ends is: Where M is the rod's total mass and L is its total length. (a) (10 points) Use the Parallel Axis Theorem to find the moment of inertia of a uniform rod about an axis that's perpendicular to the rod and passes...
please explain what equation you use to solve this problem 1. A 2.0 m long rod is hinged at one end and connected to a wall (at the hinged end). It is held at an angle of 30° from the horizontal axis by a cable attached to the rod and to the wall, as shown in Fig. 1. Suddenly, the cable snaps (so the cable is no longer applying any tension force to the rod). The moment of inertia for...
9. a. A spring has constant k-5lb./in. Its natural length is 12 inches. What is the work required to compress it to 9 inches? b. A 100 ft. cable weighs 40 lbs. Find the work done in winding the cable onto a winch, if the cable is hanging vertically c. An unknown positive charge q is placed at the origin. The force F (in Newtons) with which this charge repels a unit positive charge is given by F-kq/r, where k...
1. A 2.0 m long rod is hinged at one end and connected to a wall (at the hinged end). It is held at an angle of 30° from the horizontal axis by a cable attached to the rod and to the wall, as shown in Fig. 1. Suddenly, the cable snaps (so the cable is no longer applying any tension force to the rod). The moment of inertia for various objects can be found on the back of the...
A rectangular concrete beam measures 12 inches wide and has a depth of 26 inches. The centroid of the tension rebars is located 4 inches from the tension surface of the beam. Use fy = 60 ksi f’c = 3 ksi, compressive failure strain of concrete = 0.003. (A) Find the required tension rebars As to carry Mu = 5,700 kips-in. Show that the steel ratio does not meet the ACI requirements. (B) What can you do to meet ACI...