1. The instruction TRAP x25 causes the PC to be loaded with the memory address:
a. x0025
b. x2500
c. the contents of x0025
d. x0250
2. The instruction TRAP x23 at location x4232, causes R7 to be loaded with:
a. x4232
b. x4233
c. contents of x4232
d. contents of x4233
4. The execution of the JSR instruction at location x4202, causes R7 to be loaded with:
a. x4200
b. x4201
c. x4202
d. x4203
5. Which instruction in the LC-3 restarts the clock?
a. TRAP x30
b. RESTART
c. CLK_ST
d. No instruction can restart the clock.
1. The instruction TRAP x25 causes the PC to be loaded with the memory address:
Answer : c. the contents of x0025
2. The instruction TRAP x23 at location x4232, causes R7 to be loaded with:
Answer : a. x4232
4. The execution of the JSR instruction at location x4202, causes R7 to be loaded with:
Answer : d. x4203
5. Which instruction in the LC-3 restarts the clock?
Answer: a. TRAP x30
1. The instruction TRAP x25 causes the PC to be loaded with the memory address: a....
Problem 4 (15pts): hines iom address oing MIPS memory with data shown in hex, which are located in little-endian byte on rough 15. Show the result of the MIPS instruction "w Ss0, 4(Sa0)" for an byte orders, where $a0 4 Address Contents Address Contents 0a 1 b 2c 3d 8a 9b 10 b4 c5 6d 7e 8f 5f 13 14 15 70 (b) (10pts)Ass specified units. ume we have the following time, performance and architecture parameters in the Ec execution...
How many address lines are required for a memory containing a total at (a) 256 kB (b) 2 MB (c) 4 GB Fill in the blanks with one of IR, ALU, PC, ACC, MEMORY, FETCH PHASE or EXECUTE PHASE: (a) Data is stored in the __________ (b) Programs are stored in the ___________ (c) To be executed, an instruction is loaded into the ____________ (d) The address of an instruction to be executed is held in ______________ (e) Instructions are...
Use the following tables and the 16-bit instruction table (table.1) to: Use the following tables and the 16-bit instruction table (table.1) to: a. Decode the instruction when PC=CD2. b. Show the contents of register AC and the memory after executing the instruction, when the original value of AC=D1B0 c. Decode the instruction when PC=CD3 d. Show the contents of register AC and the memory after execution the instruction, when the original value of AC=D1B0
Instruction set architecture R: register X, Y, Opl, Op2: Operand Quantity: constant value EA: Effective memory address Opcode Operation Name MOV X, Y XCH Opl, Op2 ADD X, Y SUB X,Y SAL Op, Quantity SAR Op, Quantity Shift Arithmetic Right on Op for Quantity SHR Op Quanti AND X, Y OR X, Y XOR X, Y NOT X LOADR, A LOAD R, (A STORE R, A STORE R, (A Description Move data from Y to X Exchange Op1 with Op2...
Problem 4 (15pts): (a) (5pts) Consider the following MIPS memory with data shown in hex, which are located in memory from address 0 through 15. Show the result of the MIPS instruction "lw Ss0,4(Sa0)" for machines in little-endian byte orders, where Sa0 4. Address Contents Address Contents 9b lb 2 4 6 10 b4 c5 12 13 14 15 3d 5f 70 7 8f (b) (10pts)Assume we have the following time, performance and architecture parameters in the specified units Ec-...
A microprocessor has a decrement memory direct instruction, which subtracts 1 from the value in a memory location. The instruction has five stages: fetch opcode (two bus clock cycles), fetch operand address (five cycles), fetch operand (five cycles), subtract 1 from operand (four cycles), and store operand (two cycles). a. By what amount (in percent) will the duration of the instruction increase if we have to insert one bus wait state in each memory read and memory write operation? b....
Problem 4 (15pts): (a) (5pts) Consider the following MIPS memory with data shown in hex, which are located in memory from address 0 through 15. Show the result of the MIPS instruction "lw Ss0,4(Sa0)" for machines in little-endian byte orders, where Sa0 4. Address Contents Address Contents 9b lb 2 4 6 10 b4 c5 12 13 14 15 3d 5f 70 7 8f (b) (10pts)Assume we have the following time, performance and architecture parameters in the specified units Ec-...
The AVR provides a rich instruction set to support high-level languages. The AVR address- ing modes also simplify the access of complex data structures. The AVR has a version of the ADD instruction that includes the C flag as one of the source operands, which enables multiple- precision addition operation. The AVR also has a version of the SUB instruction that includes the C flag as one of source operands and hence is used to perform multiprecision subtraction operation. The...
1) How many bits are needed to address/uniquely identify the LC-3’s eight General Purpose Registers? 2) How many bits or bytes are at each memory location in the LC-3? 3) The minimum and maximum values for an UNSIGNED CHAR (1 byte) are? 4) The minimum and maximum values for a SIGNED CHAR (1 byte) are? 5) The LC-3 has a 16-bit address bus and is able to address up to how many memory locations? Why?/How?/Prove? I don’t want a 2...
Consider a hypothetical computer with an instruction set of only two n-but instructions. The first bit specifies the opcode, and the remaining bits specify one of the 2-1 n-bit words of main memory. The two instructions are as follows: SUBS X: Subtract the contents of location X from the accumulator, and store the result in location X and the accumulator JUMP X: Place address X in Program Counter A word in memory may contain either an instruction or a binary...