A pulley of diameter 7.00 cm is driven at 100 rpm. Find the diameter of a second pulley if it is driven by the first at 250 rpm.
As both pulleys are driven by same belt , the linear speed is equal in both case.
r is radius , d is
diameter
A pulley of diameter 7.00 cm is driven at 100 rpm. Find the diameter of a...
One pulley rotates at 560 rpm. A second pulley, connected to the first by a belt, has a diameter of 12 in and rotates at 330 rpm. Find the diameter of the first pulley.
1. The radius of a curve is 27.5m. What is the centripetal force on a 10,000kg truck going around it at 35.0 km/hr? 2. A pulley of diameter 5.00 cm is driven at 100 rpm. Find the diameter of a second pulley if it is drven by the first at 250 rpm. 3. What is the M.A. of a pulley system having 12 strands holding the resistance?
Q2. Figure Q2 shows a shaft which transmits a power of 48 kW through flat belts. Pulley A is driven by a motor which rotates at 3000 rpm. The diameter of pulley A is 400 mm and that of pulley B is 250 mm. The thickness of the belts is 4 mm and they are made of a material with density of 1100 kg/m3. Assume no sliding between pulleys and belts a) Calculate the speed of the belt and the...
4. A 5 cm diameter gear is driven by a 1 cm gear that rotates at 1 revolution per second. The 1 cm gear stalls at a torque of 1 Nm. What is the angular velocity of the 5 cm gear? 5. A 5 cm diameter gear is driven by a 1 cm gear that rotates at 1 revolution per second. The 1 cm gear stalls at a torque of 1 Nm. What is the stall torque of the 5...
A 24 inch diameter pulley driven by a horizontal belt transmits power (20 marks) (a) through a solid shaft to a 10 inch diameter pinion which drives a mating gear. The pulley weighs 300 lb to provide some fly wheel effect. The arrangement of elements, the belt tensions, and the components of the gear reactions on the pinion are as indicated in figure-3. Determine the necessary shaft diameter using ASME Code stress value for commercial shafting and shock fatigue factors...
5. A 5 cm diameter gear is driven by a1 cm gear that rotates at 1 revolution per second. The 1 cm gear stalls at a torque of 1 N m. What is the stall torque of the 5 cm gear?
A 2.3 kg , 20-cm-diameter turntable rotates at 100 rpm on frictionless bearings. Two 300 g blocks fall from above, hit the turntable simultaneously at opposite ends of a diagonal, and stick. What is the turntable's angular velocity, in rpm, just after this event
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is made from cold-drawn 1040 steel. The key is to be made from cold-drawn 1020 steel. For a safety fac- tor of 3, compute the required square key length for both shear and compression
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is made from cold-drawn 1040 steel. The key is to...
A 2.6 kg , 20-cm-diameter turntable rotates at 100 rpm on frictionless bearings. Two 400 g blocks fall from above, hit the turntable simultaneously at opposite ends of a diagonal, and stick. What is the turntable's angular velocity, in rpm, just after this event?
An overhang hollow shaft carries a 900 mm diameter pulley, whose centre is 250 mm from the centre of the nearest bearing. The weight of the pulley is 600 N and the angle of lap is 180°. The pulley is driven by a motor vertically below it. If permissible tension in the belt is 2650 N and if coefficient of friction between the belt and pulley surface is 0.3, estimate, diameters of shaft, when the internal 15. diameter is 0.6...