Question

6-12 Use Coulomb's method to determine the magnitude and direction of the total lateral force against...

6-12 Use Coulomb's method to determine the magnitude and direction of the total lateral force against the retaining wall of problem 6-5. Assume the friction angle between the wall and the soil to be 2/3*phi. Make one trial only, using an assumed failure surface at an angle of 60 degrees from horizontal.

Problem 6-5 is: Use Rankine's method to determine the magnitude and location of the resultant active force against a retaining wall 6 m high. There is a water table 2.5 m below the top of the wall and the backfill supports a uniform surcharge of 30 kN/m2. The backfill material is sand with a friction angle, phi, of 35°, a unit weight above the water table of 18.7 kN/m3, and a saturated unit weight of 21.2 kN/m3

0 0
Add a comment Improve this question Transcribed image text
Know the answer?
Add Answer to:
6-12 Use Coulomb's method to determine the magnitude and direction of the total lateral force against...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • please answer 2 and 3 i would really appreciate it :) 2. The 4 m tall...

    please answer 2 and 3 i would really appreciate it :) 2. The 4 m tall concrete retaining shown in Figure 2 has the following properties: Backfill (Coarse sand): Ym = moist unit weight = 19.2 kN/m d' = effective friction angle = 40° The groundwater table will remain far below the wall, and the wall friction angle is 20°. Assume the backfill is not sloped and the wall has no batter. The wall moves sufficiently to develop the active...

  • its problem 17.6 on foundation engineering ninth edition by Braja M.Das 17.6 ung Coulomb's earth pressures....

    its problem 17.6 on foundation engineering ninth edition by Braja M.Das 17.6 ung Coulomb's earth pressures. It is required to design a cantilever retaining wall to retain a 5.0 m high sandy backfill. The consultant suggests the dimensions and soil properties shown in Figure P17.6 and requires that the wall be checked for stability with respect to sliding and overturning based on the active earth pressures determined using 0.5 mm 110° EDT Sand y = 18.5 kN/m3 6' = 36°...

  • A 4m high, vertical retaining wall supports Silty SAND backfill with a horizontal surface. There is...

    A 4m high, vertical retaining wall supports Silty SAND backfill with a horizontal surface. There is a hydrostatic horizontal water table at 1 m below the ground surface. The soil has bulk unit weight = 20 kN/m3, effective cohesion=5 kPa, and friction angle= 30o. What is the value of the water force on the wall? At what distance above the base of the wall does it act?

  • 1 Calculate the factor of safety against overturning and sliding for the concrete retaining wall ...

    1 Calculate the factor of safety against overturning and sliding for the concrete retaining wall shown in the figure below, without taking into consideration the passive earth pressure. (50 Points) Assume that 115 lbs/cf unit weight of soil: unit weight of concrete: 150 lbs/cf angle of internal friction: 30 coefficient of friction: 0.350 0° B: 14 5' 2" Ha 14 2.5 Compaction (Soils engineering uses the symbol ys for dry density and uses the term dry unit weight. In the...

  • Problem 5 You are to examine the retaining wall shown on Figure 2. Assume that the wall height (H...

    Problem 5 You are to examine the retaining wall shown on Figure 2. Assume that the wall height (H) is equal to 12 feet, and the base width (B) is 7 feet. The wall will be approximately 200 feet long (into the page). The backfill material behind the wall is a poorly-graded sand with silt (ŚP-SM) that has an average total unit weight of 1 19 pounds per cubic foot (pcf) and an average water content of 12%. As indicated,...

  • 15 t/m' (6) Use Culmann's graphical method to find the magnitude of the total earth pressure...

    15 t/m' (6) Use Culmann's graphical method to find the magnitude of the total earth pressure on the shown retaining wall. Find the distance (x) beyond which the shown concentrated load will not affect the earth pressure on the wall. Sand: 6 m 1:4 y 1.86 um?

  • a) What is the factor of safety against overturning? b) What is the distance from A...

    a) What is the factor of safety against overturning? b) What is the distance from A the normal for N acts? Is 100% of the base in contact with the soil based on this information? c) If the foundation soil is sand and the interface friction angle is 37 degrees, what is the factor of safety against sliding d) What is the factor of safety against bearing capacity failure (use Meyerhoffs Method) if the ultimate capacity of the foundation soil...

  • help please A square footing is founded at 3-ft depth below ground surface as shown in...

    help please A square footing is founded at 3-ft depth below ground surface as shown in Fig1, The factored axial load acting on the square footing is 140 kips, Determine the size of the footing (B x B) if the Factor of Safety (F.S.) is 3.0. Ground surface ЗА B-? Silty Sand Fig.1 A 68-ft long pre-stressed concrete pile with square cross section (14 inch) is driven into the soil profile shown in Fig. 2. Compute the ultimate compressive load...

  • Question 2 (a) A 4 m high masonry retaining wall of width 1.8 is built to...

    Question 2 (a) A 4 m high masonry retaining wall of width 1.8 is built to retain a 2-layered soil profile shown in Figure 2 on Bonham Road on Hong Kong Island with a surface sucharge of 20 kPa. The soil parameters are given in the figure. During raining season, ground water rises to interface between Soil 1 and Soil 2. Assume that there is no friction between the vertical wall and the soils. The sliding friction angle between the...

  • A proposed residential development of a single tower is to be built on a sloping site...

    A proposed residential development of a single tower is to be built on a sloping site as shown in Figure 1. The site has a (W1m x 25m wide building zone. A level platform has to be created by building a permanent retaining structure outside the building zone but within the (W2m x (W2m wide site boundary. A temporary slope, which may extend outside the site boundary, has to be formed in advance for construction of the retaining structure. ---...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT