A hot burrito is placed on a cold plate. The rate at which the burrito cools...

Question

Question

A hot burrito is placed on a cold plate. The rate at which the burrito cools down depends on:

a. It's cross sectional area

b. The surface area of the plate

c. The 4th power it's surface temperature

d. The temperature gradient between it's center and the surface of the plate

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

The surface of a hot plate is made up of 15.0 mm thick aluminum with a...

The surface of a hot plate is made up of 15.0 mm thick aluminum with a 65 cm2 cross sectional area. If the hot plate maintains a temperature of 80.5 degrees C underneath the surface and the air temperature in the lab is 22.8 degrees C, how much heat can be transferred through the hot plate?
A hot bath at T = 92.2 °C is connected to a cold bath at T...

A hot bath at T = 92.2 °C is connected to a cold bath at T = 15.6 °C by an insulated metal rod as shown in the diagram (Figure 1). The metal rod is made from two metals, aluminium is next to the hot bath and has a length li = 50.5 cm, steel makes up the remainder of the rod. The junction between the aluminium and steel has a temperature T; = 40.2 °C. The rate of energy...
A hot bath at Th 82.2 °C is connected to a cold bath at T 13.9°C...

A hot bath at Th 82.2 °C is connected to a cold bath at T 13.9°C by an insulated metal rod as shown in the diagram (Figure 1). The metal rod is made from two metals, aluminium is next to the hot bath and has a length 11-65.2 cm, steel makes up the remainder of the rod. The junction between the aluminium and steel has a temperature T 55.4 °C. The rate of energy flow through the rods is P=...

A hot reservoir with a temperature of 687 K is 0.58 m away from a cold...

A hot reservoir with a temperature of 687 K is 0.58 m away from a cold reservoir with a temperature of 358 K. The two reservoirs are insulated from each other except for a rod of brass (k = 109 W/m-K) that has a cross-sectional area of 0.058 m2. The entire system is allowed to reach a steady-state condition. 1) How much energy is transferred by heat between the hot reservoir and the cold reservoir in ten minutes? J Submit...
A hot reservoir with a temperature of 687 K is 0.58 m away from a cold...

A hot reservoir with a temperature of 687 K is 0.58 m away from a cold reservoir with a temperature of 358 K. The two reservoirs are insulated from each other except for a rod of brass (k = 109 W/m-K) that has a cross-sectional area of 0.058 m2. The entire system is allowed to reach a steady-state condition. 1) How much energy is transferred by heat between the hot reservoir and the cold reservoir in ten minutes? J Submit...
dit The rate at which a body cools also depends on its exposed surface area S....

dit The rate at which a body cools also depends on its exposed surface area S. If Sis a constant, then a modification of (2) given in Section 3.1, dr kS(T-T). where k < and Te is a constant. Suppose that two cups A and Bare filled with coffee at the same time. Initially, the temperature of the coffee is 66* C. The exposed surface area of the coffee in cup is twice the surface area of the coffee in...

(C1HW13) A baking dish is removed from a hot oven and placed on a cooling rack....

(C1HW13) A baking dish is removed from a hot oven and placed on a cooling rack. As the dish cools down to 32.0°C from 168°C, its net radiant power decreases to 11.0 W. What was the net radiant power of the baking dish when it was first removed from the oven? Assume that the temperature in the kitchen remains at 22.0°C as the dish cools.
Problem 1: A metallic fin of length is attached to a hot surface (at To) and is exposed to cold a...

Problem 1: A metallic fin of length is attached to a hot surface (at To) and is exposed to cold air at To. The temperature at the end of the fin is T1. The governing equation for the temperature along the length of the fin is given below where h is the heat transfer coefficient, k is the thermal conductivity of metal, P is the perimeter of the fin, and A is the cross-sectional area of the fin. (a) Do...
A plate is placed in a large vacuum chamber to control its cooling rate. To prevent...

A plate is placed in a large vacuum chamber to control its cooling rate. To prevent cracking, the temperature gradient in the plate cannot exceed 15 K/mm at any point during cooling. The plate is initially at 900 K with an emissivity of 0.8 and thermal conductivity of 1.5 W/m.K. Assume that one of the surface of the plate is insulated and the other is exposed to the chamber, and the chamber walls are considered as black surface. Apply the...

1. A plate is placed in a large vacuum chamber to control its cooling rate. To...

1. A plate is placed in a large vacuum chamber to control its cooling rate. To prevent cracking, the temperature gradient in the plate cannot exceed 15 K/mm at any point during cooling. The plate is initially at 900 K with an emissivity of 0.8 and thermal conductivity of 1.5 W/mK. Assume that one of the surface of the plate is insulated and the other is exposed to the chamber, and the chamber walls are considered as black surface. Apply...