On an oscilloscope you count 4 cycles across 55 minor time divisions on an oscilloscope screen. The time...
On an oscilloscope you count 4 cycles across 55
minor time divisions on an oscilloscope screen.
The time sweep is set to 20 milli seconds.
The voltage peak is measured to be 22 volts.
What is the frequency?
Homework Answers
Add Answer to:
On an oscilloscope you count 4 cycles across 55
minor time divisions on an oscilloscope screen.
The time...
1. You count 12 cycles across 8.5 time divisions on an oscilloscope screen. The time sweep...
1. You count 12 cycles across 8.5 time divisions on an oscilloscope screen. The time sweep is set to 45 micro seconds. The voltage peak is measured to be 22 volts. What is the frequency in HZ? (Use three significant figures or N/A if no answer.) 2. You plot some data of Real Frequency versus HP Dial Frequency and get a linear trend of y = 1.31 x + 230. To what must you set the HP Dial Frequency in...
A sine wave signal is displayed on the screen of an oscilloscope. 6 peak-to-peak divisions are...
A sine wave signal is displayed on the screen of an oscilloscope. 6 peak-to-peak divisions are measured vertically and 8 peak-to-peak divisions horizontally. The voltage control is on the 2 volts / div scale and the sweep control is on the 5ms scale. The signal period is: a. 0.03 seconds b. 0.04 seconds c. 4 seconds d. 0.005 seconds
Analog Oscilloscope Setup: 1. Turn on the power to the oscilloscope. 2. Connect the function gene...
Analog Oscilloscope Setup: 1. Turn on the power to the oscilloscope. 2. Connect the function generator to the Channel 1 input on the oscilloscope 3. In the Vertical Control Group, set the Channel 1 AC/GND/DC switch to AC. 4. Set the Volts-per-Division knob 5. Intensity knob: adjust the signal intensity and focus to a comfortable level by using the intensity and focus knobs, respectively Set the seconds-per-division knob 6. Assignment Procedures: 1. Using the settings completed above, answer the following...
hy I need answers of these questions according to data sheet. thank you DATA SHEET PARTI...
hy I need answers of these questions according to data
sheet. thank you
DATA SHEET PARTI TIME/DIV ims VOLTS/DIV=_IV PEAK VOLTAGE V_47 toms TIME/DIV=_ms VOLTS/DIV-5V PEAK VOLTAGE V_42 PERIOD TO_loms PERIOD T- PART 1 SINEWAVE Vrms (VOLTS) VP (VOLTS) (Voltmeter) (oscilloscope) 7:07 10 3.57 5 2: 78 4 2.10 3 2 Slope=0.707V TIME/DIV=_ams VOLTS/DIVE PEAK VOLTAGE V=_41_ PERIOD T=_toms PART III SQUAREWAVE VAMS (VOLTS) VP (VOLTS) (Voltmeter) (oscilloscope) 10.9 do 542 S 4.4 4 3:3 고 2-2 Slope 0-92-1v PART...
You place an AC voltage signal of amplitude 1.4 V and with a frequency of 1100.0...
You place an AC voltage signal of amplitude 1.4 V and with a frequency of 1100.0 Hz, into the input of an oscilloscope. (Note, you will not include units in your answers.) (a) Find the distance displayed on the screen of the oscilloscope for a full wave, if the sweep speed is adjusted to 182 µsec/DIV. divisions (b) If the vertical gain is set to 0.47 V/DIV, how many divisions will the wave span from peak-to-peak of the wave? divisions
*USE Multisim( Provide Pictures of work on Multisim for each step) and Fill the Tables Below...
*USE Multisim( Provide Pictures of work on Multisim for each
step) and Fill the Tables Below
PROCEDURE: Review the front panel controls in each of the major groups. Then turn on the oscilloscope, select Chl, set the SEC/DIV to 0.1 ms/div, select AUTO triggering, and obtain a line across the face of the CRT. Although many of the measurements described in this experiment are automated in newer scopes, it is useful to learn to make these measurements manually. Turn on...
0.0002 0.0004 0.0006 + 6014 0.0018 0.002 0.0022 1.1) The figure above is a snapshot of an oscilloscope screen sho...
0.0002 0.0004 0.0006 + 6014 0.0018 0.002 0.0022 1.1) The figure above is a snapshot of an oscilloscope screen showing the potential (in volts) vs time (in seconds) measured across a resistor of an RL circuit during a de-energizing phase. The series resistance of the circuit is 600 Ohms. What is the value of the self-inductance of the circuit?
Question 4) (a) In an experiment to measure the capacitance of a capacitor an oscilloscope was...
Question 4) (a) In an experiment to measure the capacitance of a capacitor an oscilloscope was connected across the capacitor. The diagram below shows an AC waveform that is displayed on the oscilloscope's screen. The oscilloscope settings are: Y-axis is the voltage 4.0 V per division, X- axis is the time base 1.0 ms per division. For the waveform shown, (0) What is the peak voltage across the capacitor? (1) (ii) Calculate the r.m.s voltage across the capacitor. (2) (iii)...
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4...
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4 volt amplitude, 100 us seconds/div, and 2 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal into focus so that it displays a sine wave? The oscilloscope display below is connected to a sine wave of 150 Hz frequency , 2 ms seconds/div, and 1 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal...
#6 table 2 8 LABORATORY REPORT 1C. TIME/DIV-S IC VOLTS/DIV-SV A VOLTS/DIV V ov o v...
#6
table 2
8 LABORATORY REPORT 1C. TIME/DIV-S IC VOLTS/DIV-SV A VOLTS/DIV V ov o v 0 s 2A. TIME/DIN-S2B. TIME/DIV 2C TIME/DIV-mS 2C. VOLTS/DIV o V 0 s 60033 0 s 3A. TIME/DIV-m 3A, VOLTS/DIV=-, 3B. TIME/DIV-1m 3B. VOLTS/DIV o v 0 s 0 s 388 Physics Laboratory Mamual Loyd A. TIME/DIV- ms 4A. VOLTS/DIV-LV o v ov 0 s 0 s 0 s Data Table 1 X Data Table 2 Voltmeter (V Voltmeter V 1.00 2.00 3.00 4.00...
Analog Oscilloscope Setup: 1. Turn on the power to the oscilloscope. 2. Connect the function generator to the Channel 1 input on the oscilloscope 3. In the Vertical Control Group, set the Channel 1 AC/GND/DC switch to AC. 4. Set the Volts-per-Division knob 5. Intensity knob: adjust the signal intensity and focus to a comfortable level by using the intensity and focus knobs, respectively Set the seconds-per-division knob 6. Assignment Procedures: 1. Using the settings completed above, answer the following...
hy I need answers of these questions according to data
sheet. thank you
DATA SHEET PARTI TIME/DIV ims VOLTS/DIV=_IV PEAK VOLTAGE V_47 toms TIME/DIV=_ms VOLTS/DIV-5V PEAK VOLTAGE V_42 PERIOD TO_loms PERIOD T- PART 1 SINEWAVE Vrms (VOLTS) VP (VOLTS) (Voltmeter) (oscilloscope) 7:07 10 3.57 5 2: 78 4 2.10 3 2 Slope=0.707V TIME/DIV=_ams VOLTS/DIVE PEAK VOLTAGE V=_41_ PERIOD T=_toms PART III SQUAREWAVE VAMS (VOLTS) VP (VOLTS) (Voltmeter) (oscilloscope) 10.9 do 542 S 4.4 4 3:3 고 2-2 Slope 0-92-1v PART...
*USE Multisim( Provide Pictures of work on Multisim for each
step) and Fill the Tables Below
PROCEDURE: Review the front panel controls in each of the major groups. Then turn on the oscilloscope, select Chl, set the SEC/DIV to 0.1 ms/div, select AUTO triggering, and obtain a line across the face of the CRT. Although many of the measurements described in this experiment are automated in newer scopes, it is useful to learn to make these measurements manually. Turn on...
0.0002 0.0004 0.0006 + 6014 0.0018 0.002 0.0022 1.1) The figure above is a snapshot of an oscilloscope screen showing the potential (in volts) vs time (in seconds) measured across a resistor of an RL circuit during a de-energizing phase. The series resistance of the circuit is 600 Ohms. What is the value of the self-inductance of the circuit?
Question 4) (a) In an experiment to measure the capacitance of a capacitor an oscilloscope was connected across the capacitor. The diagram below shows an AC waveform that is displayed on the oscilloscope's screen. The oscilloscope settings are: Y-axis is the voltage 4.0 V per division, X- axis is the time base 1.0 ms per division. For the waveform shown, (0) What is the peak voltage across the capacitor? (1) (ii) Calculate the r.m.s voltage across the capacitor. (2) (iii)...
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4 volt amplitude, 100 us seconds/div, and 2 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal into focus so that it displays a sine wave? The oscilloscope display below is connected to a sine wave of 150 Hz frequency , 2 ms seconds/div, and 1 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal...
#6
table 2
8 LABORATORY REPORT 1C. TIME/DIV-S IC VOLTS/DIV-SV A VOLTS/DIV V ov o v 0 s 2A. TIME/DIN-S2B. TIME/DIV 2C TIME/DIV-mS 2C. VOLTS/DIV o V 0 s 60033 0 s 3A. TIME/DIV-m 3A, VOLTS/DIV=-, 3B. TIME/DIV-1m 3B. VOLTS/DIV o v 0 s 0 s 388 Physics Laboratory Mamual Loyd A. TIME/DIV- ms 4A. VOLTS/DIV-LV o v ov 0 s 0 s 0 s Data Table 1 X Data Table 2 Voltmeter (V Voltmeter V 1.00 2.00 3.00 4.00...
Most questions answered within 3 hours.
-
How much must I invest today if I want to withdraw 1/3 of my
original investment...
asked 14 minutes ago -
What is meant by a “term premium”?
What can explain such a premium? Is it a...
asked 1 hour ago -
23. Which molecule has only covalent bonds? A. CO2 B. Al2O3 C.
Mg3N2
24. The octet...
asked 2 hours ago -
the
total pressure for a mixture of N2O4 and NO2 is 2.20 atm. If Kp=
7.10...
asked 2 hours ago -
Delaware Corp. prepared a master budget that included $22,385
for direct materials, $28,600 for direct labor,...
asked 2 hours ago -
For pesticide HCB (hexachlorobenzene), its logarithmic partition
coefficient log Kow is 5.6. What would be the...
asked 2 hours ago -
A chemist requires 0.422 mil Na2CO3 for a reaction. How many
grams does this correspond to?
asked 2 hours ago -
If the vapor pressure of carvone is approximately 9.4 torr at 99
°C, approximately how much...
asked 2 hours ago -
A juice bottling company is carrying out a test at 10%
significance that the mean population...
asked 3 hours ago -
What is the reflectivity (in percent) needed to keep water at a
temperature near its freezing...
asked 3 hours ago -
Suppose that the average surface temperature of Earth is 300K.
Assume this is uniform over its...
asked 3 hours ago -
Draw the condensed structural formula for alkenes and alkynes or
the line-angle structural formula for cycloalkenes...
asked 3 hours ago