A tank of glycerine is to be added to the live load on a floor. Glycerine...
A tank of glycerine is to be added to the live load on a floor. Glycerine has a specific gravity of 1.258. How much would 50 gallons of glycerine weigh?
Homework Answers
Given specific gravity of glycerine = 1.258
Density of water = 62.4 pound per cubic feet.
Specific gravity of glycerine =
Density of glycerine/ density of water.
Density of glycerine = 62.4 x 1.258 = 78.5 lb/ft3.
Given volume of glycerine = 50 gallons = 6.684 cubic feet.
Total weight of glycerine = density x volume.
6.684 x 78.5 = 524.7 pounds.
Add Answer to:
A tank of glycerine is to be added to the live load on a floor.
Glycerine...
Determine the dead load and live load for a floor in a light manufacturing warehouse/office complex...
Determine the dead load and live load for a floor in a light manufacturing warehouse/office complex in which any area can be used for storage. Assume that there will be no ceiling or floor finish and that the floors are 4-in. reinforced concrete. Allowance for mechanical ducts should be provided.
the beam is loaded uniformly from the floor with a live load of 80 pounds per...
the beam is loaded uniformly from the floor with a live load of
80 pounds per square foot (psf) and a dead load in addition to the
beam self-weight of 60 psf. the beam will have full lateral support
provided by the floor deck, and a compact section will be selected.
Use A992 steel. Design a W-shape floor beam for the intermediate
beam marked A on the floor plan shown below.
a) Use LRFD.
b) Use ASD.
Is loaded uniformly...
live load on the floor plan in Figure P2.4 is 60 lb/t2 Establish the loading for...
live load on the floor plan in Figure P2.4 is 60 lb/t2 Establish the loading for members (a) floor beam B3, (b) floor beam B4, (c) girder G3, and girder G4. Consider the live load reduction if permitted by the ASCE standard. Figure P2.4 6 @ 6.67.= 4041 C4 A I B2 G1 B3 B4 2@10.=20. Tc2 G2 G3 B1 5@8. = 40. C-I I_I C3 Cl 400
А w18 x 40 steel spandrel (edge) beam spans 20'. The beam supports a uniform floor live load of 1 kip/ft and a uniform floor dead load of 0.5 kip/ft. The beam also supports brick veneer weigh...
А w18 x 40 steel spandrel (edge) beam spans 20'. The beam supports a uniform floor live load of 1 kip/ft and a uniform floor dead load of 0.5 kip/ft. The beam also supports brick veneer weighing .6 kip/ft as a uniform dead load. The maximum allowable total load deflection for beams supporting masonry (brick or block) is L/640. Calculate the live load and total load deflections. Do the live load and total load deflections exceed the allowable deflections for...
5" Floor Slab (R/C) Other Dead Load /O Live Load =125 Max, LL Deflection = L...
5" Floor Slab (R/C) Other Dead Load /O Live Load =125 Max, LL Deflection = L / 360 s-joist spacing L- joist span A floor system consists of open-web steel joists spaced as shown in figure. Assume the slab provides continuous lateral support. Using your own data determine the following: a-) The factored load (wu) on one joist. b-) Design and select a K-series joist. Solution:
Considering the floor layout shown in Fig. 1 and assuming a distribute Live load of 150...
Considering the floor layout shown in Fig. 1 and assuming a distribute Live load of 150 PSF, it is required to: Calculate the live load transferred to beams B1, B2 and B3 and Column C1. 3 4 (5 6 30.00 ft 6.00 6.00 6.00 6.00 6 00 HT A B1 B2 20.00 ft 20.00 ft C1 B3 B (В + B1 B2 20.00 ft 20.00 ft +++ C) 6.00 6.00 6.00 6.00 6.00 30.00 ft 3 5 6 Figure 1
The plan view of a typical floor of a four-story heavy storage facility is shown below. The floor and roof live load is...
The plan view of a typical floor of a four-story heavy storage facility is shown below. The floor and roof live load is 250 psf, and the dead load on all foors and the roof consists of the structure self-weight plus 10 psf for utilities. W 12:96 beams are spaced at 12 ft; w 18x106 reinforced one-way concrete floor/roof slab is 8" thick, each story is 12' high, and the reinforced concrete columns have a 14" x 14" cross-section girders...
victoriacollege.instructure.com 20 Question 3 An open top tank is filled with a liquid that has a...
victoriacollege.instructure.com 20 Question 3 An open top tank is filled with a liquid that has a specific gravity of 1.735. The liq exerts a head pressure of 450 inches w.c. What is the level in inches? 780.7500 Question 4 20 pt An open top tank is filled with a liquid that has a specific gravity of 0.873. The liquid exerts a head pressure of 200 inches w.c. What is the level in inches? 229.0950 Question 5 20 pts A sealed...
6. The figure below shows the floor framing plan for an office building. The roof has the same fr...
6. The figure below shows the floor framing plan for an office building. The roof has the same framing plan as the floor. Select a W12 section for Column C1 in the first floor and assume the same column will be used for Column C2 in the second floor. Floor loads (applied on the 2 floor; dead load of 200 psf and live load of 300 psf Roof loads (applied on the roof: dead load of 100 psf and roof...
Suppose a conical tank (think of an ice cream cone, point down) has a capacity of...
Suppose a conical tank (think of an ice cream cone, point down) has a capacity of 7 gallons, and that 3 gallons of water are in it already. Water is added at a rate of 6 gallons per minute, but the cone springs a leak near its tip after 10 seconds. Water exits the tank at a rate determined by Torricelli's Law, v2gh (where v is the linear velocity of the water, g the acceleration due to gravity, and h...
Determine the dead load and live load for a floor in a light manufacturing warehouse/office complex in which any area can be used for storage. Assume that there will be no ceiling or floor finish and that the floors are 4-in. reinforced concrete. Allowance for mechanical ducts should be provided.
the beam is loaded uniformly from the floor with a live load of
80 pounds per square foot (psf) and a dead load in addition to the
beam self-weight of 60 psf. the beam will have full lateral support
provided by the floor deck, and a compact section will be selected.
Use A992 steel. Design a W-shape floor beam for the intermediate
beam marked A on the floor plan shown below.
a) Use LRFD.
b) Use ASD.
Is loaded uniformly...
live load on the floor plan in Figure P2.4 is 60 lb/t2 Establish the loading for members (a) floor beam B3, (b) floor beam B4, (c) girder G3, and girder G4. Consider the live load reduction if permitted by the ASCE standard. Figure P2.4 6 @ 6.67.= 4041 C4 A I B2 G1 B3 B4 2@10.=20. Tc2 G2 G3 B1 5@8. = 40. C-I I_I C3 Cl 400
А w18 x 40 steel spandrel (edge) beam spans 20'. The beam supports a uniform floor live load of 1 kip/ft and a uniform floor dead load of 0.5 kip/ft. The beam also supports brick veneer weighing .6 kip/ft as a uniform dead load. The maximum allowable total load deflection for beams supporting masonry (brick or block) is L/640. Calculate the live load and total load deflections. Do the live load and total load deflections exceed the allowable deflections for...
5" Floor Slab (R/C) Other Dead Load /O Live Load =125 Max, LL Deflection = L / 360 s-joist spacing L- joist span A floor system consists of open-web steel joists spaced as shown in figure. Assume the slab provides continuous lateral support. Using your own data determine the following: a-) The factored load (wu) on one joist. b-) Design and select a K-series joist. Solution:
Considering the floor layout shown in Fig. 1 and assuming a distribute Live load of 150 PSF, it is required to: Calculate the live load transferred to beams B1, B2 and B3 and Column C1. 3 4 (5 6 30.00 ft 6.00 6.00 6.00 6.00 6 00 HT A B1 B2 20.00 ft 20.00 ft C1 B3 B (В + B1 B2 20.00 ft 20.00 ft +++ C) 6.00 6.00 6.00 6.00 6.00 30.00 ft 3 5 6 Figure 1
The plan view of a typical floor of a four-story heavy storage facility is shown below. The floor and roof live load is 250 psf, and the dead load on all foors and the roof consists of the structure self-weight plus 10 psf for utilities. W 12:96 beams are spaced at 12 ft; w 18x106 reinforced one-way concrete floor/roof slab is 8" thick, each story is 12' high, and the reinforced concrete columns have a 14" x 14" cross-section girders...
victoriacollege.instructure.com 20 Question 3 An open top tank is filled with a liquid that has a specific gravity of 1.735. The liq exerts a head pressure of 450 inches w.c. What is the level in inches? 780.7500 Question 4 20 pt An open top tank is filled with a liquid that has a specific gravity of 0.873. The liquid exerts a head pressure of 200 inches w.c. What is the level in inches? 229.0950 Question 5 20 pts A sealed...
6. The figure below shows the floor framing plan for an office building. The roof has the same framing plan as the floor. Select a W12 section for Column C1 in the first floor and assume the same column will be used for Column C2 in the second floor. Floor loads (applied on the 2 floor; dead load of 200 psf and live load of 300 psf Roof loads (applied on the roof: dead load of 100 psf and roof...
Suppose a conical tank (think of an ice cream cone, point down) has a capacity of 7 gallons, and that 3 gallons of water are in it already. Water is added at a rate of 6 gallons per minute, but the cone springs a leak near its tip after 10 seconds. Water exits the tank at a rate determined by Torricelli's Law, v2gh (where v is the linear velocity of the water, g the acceleration due to gravity, and h...
Most questions answered within 3 hours.
-
Write a program to solve the Josephus problem, with the following
modification:
Sample Input:
./a.out n...
asked 1 hour ago -
At the start of a CD it is spinning at a rate of 525 rpm
(revolutions...
asked 2 hours ago -
4. Without doing any calculations, predict whether the observed
∆T would increase, decrease or remain the...
asked 3 hours ago -
Based on the range, which of the following sets of scores has
the greatest variability? 3,...
asked 4 hours ago -
Ripples in a pond travel at a velocity of 3 m/s with one peak
passing a...
asked 4 hours ago -
A man stands on the roof of a building of height 13.0 mm and
throws a...
asked 4 hours ago -
The extent to which assets are financed by borrowed funds and
other liabilities is indicated by:...
asked 5 hours ago -
Explain in detail
Germany is the fifth largest economy
explain what goods and services Germany specializes...
asked 5 hours ago -
The density of platinum is 21.45 g/mL. If a cube of platinum
with a mass of...
asked 6 hours ago -
Accounts Receivable
Sales
A/R Posting
Extended Sales Invoice
Packing Slip
Compare invoice to packing slip 2...
asked 6 hours ago -
Michaella, age 23, is a full-time law student and is claimed by
her parents as a...
asked 6 hours ago -
Why are polymers not typically casted into products?
asked 6 hours ago