5. For a grain conveyor system, determine the conveyor speed required to get a flow of 6400 kg/h if the applied weight (i.e. force) on a 1.1 m platform is 300 N.
6. Water is flowing through a pipe with a 2.25 inch diameter with a flow rate of 80.3 gal/h. Convert the flow rate into (a.) kg/h; and (b.) m/s
5. For a grain conveyor system, determine the conveyor speed required to get a flow of...
I need help with this whole page. I got them all wrong Determine the approximate pressure change in 4.00 meter acceleration of 2.00 meters per second Euler Eq 18 Water flows up through the vertical pipe at a flow rate of 0.0300 m'/s and h is 508.6 mm velocity and static pressure at point D? (This can be worked via two methods, outline two algebra, and numerically complete a solution. Check your work by the other method Pascals along a...
4. An old, rough-surfaced, 2-m-diameter concrete pipe with a Manning coefficient of 0.025 carries water at a rate of 5.0 m'/s when it is half ful. This pipe is to be replaced by a new smooth pipe with a Manning coefficient of 0.012. Determine the diameter of the new pipe if it also is to flow half full with a flow rate of 5.0 m'/s Water initially flowing in the horizontal section of pipe of diameter 12.00 cm shown in...
the water level. If the rate of flow from the leak is equal 16.0 m below 2.50 X 10-3 m3/min, determine (a) the speed the water leaves the hole and (b) the diameter of the hole. to at which A village maintains a large tank with an open top, contain- ing water for emergencies. The water can drain from the tank through a hose of diame ter 6.60 cm. The hose ends with a nozzle of diameter 2.20 cm. A...
Q1. (a) For a flow phenomenon governed mainly by viscous forces, derive the scale factors for velocity, force and power in terms of 24, , and I, where subscripts L, p and u are length, density and dynamic viscosity respectively and is the ratio of the value of "x" in the prototype to the value of "x" in the model. [4 marks) (b) Volumetric flow rate (discharge) Q through a circular pipe with diameter D can be measured by measuring...
please clearly indicate answer(s) 1. As shown in the figure, using a 6-m-long, 100 mm diameter pipe and assuming a friction factor f-0.02, investigate the likelhood of cavitation if h-4 m and h = 3m Water temperature is 25 degrees Centigrade, 5101325 KP kinematic viscosity =156 m2/sec, flow velocity = 4 m/sec, neglect minor losses using 2. At the deign flow rate read the pump characteristics if the 6 in impeller is used (power, efficiency, head) 3. If the angular...
Water at 320 K and a flow rate of 5 kg/s enters a black, thin-walled tube, which passes through a large furnace whose walls and air are at a temperature of 700 K. The diameter and length of the tube are 0.25 m and 8 m, respectively. Convection coefficients associated with water flow through the tube and airflow over the tube are 300 W/m2K and 50 W/m2.K, respectively. Tube, D-0.25 m L-8 me-1 Air 7-700 K Water -5 kas -Fumace,...
A penny is submerged in a glass of water and held up horizontally by a string. The top of the penny experiences a pressure of 300 N/m2 above atmospheric pressure. What pressure is incident on the bottom surface of the penny? A. just the pressure of the atmosphere B. about 150 N/m2 above atmospheric pressure C. 0 N/m2 D. about 300 N/m2 above atmospheric pressure The applied force to a hydraulic jack is 24 N to an area of 20...
Objective To determine the force generated by a jet of water striking on a surface Description of apparatus The supply is led to a vertical pipe terminating in a tapered nozzle. This produces a jet of water which impinges on the vane in the form of a Flat Plate, Hemispherical Cup, Conical Plate or 30° Angled Plate. The nozzle and vane are contained within a transparent cylinder; at the base of the cylinder there is an outlet by which the...
CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200 mm when the difference of pressure head between the ends of the pipe 500 m apart is 4 m of water. Take the value off= 0.009 in the formula hl= a) 19.5e/s b)2.0es e)03 m's d) 29.3 e/s 2. A scale 1:50 scale model of ship is towed through sea water at a speed of 1 ms. A force of 2 N is required...
Question 1 Question 2: Question 3: Question 4: Question 5: Question 6: Question 7: Question 8: Please number each question. Thank you Question 1 Not yet answered Marked out of 4.00 Flag question If the number density of electrons in a wire is n 1.00 x 1028 m-3, at what drift velocity must they travel through a wire of diameter d 0.560 mm to deliver a current of 7.20 A? Give your answer in mm s1 to 3 significant figures...