A horizontal venturi meter (160mm * 80mm) used to measure the flow of oil of sp.gr...
A horizontal venturi meter (160mm * 80mm) used to measure the flow of oil of sp.gr =0.8. determine the deflection of oil -mercury gauge, if discharge oil is 50 lit/s
Note: Please write the solution in an official, clear, and clean manner
Homework Answers
Add Answer to:
A horizontal venturi meter (160mm *
80mm) used to measure the flow of oil of
sp.gr...
A venturi meter with a diameter of 30 cm at the entrance and 15 cm at...
A venturi meter with a diameter of 30 cm at the entrance and 15
cm at the throat, is connected to a vertical pipe of diameter 30cm
carrying oil of specific gravity 0.9. The difference in elevation
of the throat section and the entrance of the venturi meter is 30
cm. The mercury manometer shows a gauge deflection of x =
1000mm.
Determine
1) the discharge of oil; and
2) the pressure difference between the entrance section and
throat section....
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
5. A venturi flow meter is to be used to measure the flow of air at low velocities, with air mass...
5. A venturi flow meter is to be used to measure the flow of air at low velocities, with air mass flow rate being given by 11/2 CA 2P (p2) RTPP2) where C is an empirically determined discharge coefficient, A is the throat flow area, pi and pp are the upstream and throat pressures, Ti is the absolute upstream temperature, and R is the gas constant for air. We want to calibrate this meter and to determine C to within...
A venturi meter was installed in a pipe to measure the flow of the water inside....
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
Q1. (a) Derive Bernoulli’s equation and state its limitations [5 marks] (b) A horizontal venturimeter with inlet diameter...
Q1. (a) Derive Bernoulli’s equation and state its limitations [5 marks] (b) A horizontal venturimeter with inlet diameter 20cm and throat diameter 10cm is used to measure the flow of oil of sp.gr 0.8. The discharge of oil through venturimeter is 60 litres/s. Find the reading of oil mercury differential manometer in meters. Take Cd = 0.98 and Sp. Gravity of mercury 13.6. [5 marks]
(c) A venturi meter is mounted in a pipeline of diameter 150 mm, which is inclined at 30° from the horizontal. Water is flowing upwards through the pipeline. The throat diameter of the venturi meter...
(c) A venturi meter is mounted in a pipeline of diameter 150 mm, which is inclined at 30° from the horizontal. Water is flowing upwards through the pipeline. The throat diameter of the venturi meter is 90 mm. One static pressure tapping is located at the throat and another 0.3 m upstream in the pipeline. The pressure difference measured between the two tappings is 200 mm of mercury. The coefficient of discharge for the meter is 0.97. Determine the actual...
Venturi meter provided in a vertical pipeline carries oil of specific gravity 0.88 as shown in...
Venturi meter provided in a vertical pipeline carries oil of specific gravity 0.88 as shown in the Figure below. The diameter at the entrance and throat are 30 cm and 15 cm, respectively. A U-tube manometer filled with mercury of density 13600kg/m3 is connected to the entrance and throat of the meter . The height difference between the throat and entrance is 30cm. if the actual flow rate is 80 L/s and the coefficient of discharge of the meter is...
An orifice meter with a 2 inch diameter opening is used to measure the flow rate...
An orifice meter with a 2 inch diameter opening is used to measure the flow rate of water through a horizontal 3 inch diameter pipe. A mercury manometer is used to measure the pressure difference across the orifice. If the differential height of the manometer is 7 inches, determine the volumetric flowrate (gal/min) of water through the pipe. You may assume the discharge coefficient is 0.6.
A venturi meter is used to measure the flow speed of a fluid in a pipe....
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (the figure); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed V and then through a narrow ''throat'' of cross-sectional area a with speed v. A manometer connects the wider portion of the...
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected...
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (Fig. 14-55); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed V and then through a narrow ''throat'' of cross-sectional area a with speed v. A manometer connects the wider portion of the...
A venturi meter with a diameter of 30 cm at the entrance and 15
cm at the throat, is connected to a vertical pipe of diameter 30cm
carrying oil of specific gravity 0.9. The difference in elevation
of the throat section and the entrance of the venturi meter is 30
cm. The mercury manometer shows a gauge deflection of x =
1000mm.
Determine
1) the discharge of oil; and
2) the pressure difference between the entrance section and
throat section....
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
5. A venturi flow meter is to be used to measure the flow of air at low velocities, with air mass flow rate being given by 11/2 CA 2P (p2) RTPP2) where C is an empirically determined discharge coefficient, A is the throat flow area, pi and pp are the upstream and throat pressures, Ti is the absolute upstream temperature, and R is the gas constant for air. We want to calibrate this meter and to determine C to within...
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
(c) A venturi meter is mounted in a pipeline of diameter 150 mm, which is inclined at 30° from the horizontal. Water is flowing upwards through the pipeline. The throat diameter of the venturi meter is 90 mm. One static pressure tapping is located at the throat and another 0.3 m upstream in the pipeline. The pressure difference measured between the two tappings is 200 mm of mercury. The coefficient of discharge for the meter is 0.97. Determine the actual...
Most questions answered within 3 hours.
-
A normal distribution of scores has a mean of 240 and a standard
deviation of 40....
asked 1 second ago -
Create a Namespaces.h header file containing a namespace
declaration yourname. The declaration should include a method...
asked 8 minutes ago -
Herrod Catering uses two measures of activity, jobs and meals,
in the cost formulas in its...
asked 8 minutes ago -
Suppose a particle has zero potential energy for x
< 0, a constant value V, for...
asked 5 minutes ago -
As a technician in a large pharmaceutical research firm, you
need to produce 200. mL of...
asked 10 minutes ago -
how a person can still function with different parts
of the brain being damaged or removed
asked 12 minutes ago -
Cells that contain two of each of the chromosomes in a set are
known as:
Haploid...
asked 22 minutes ago -
The United States Department of Agriculture (USDA) found that
the proportion of young adults ages 20–39...
asked 25 minutes ago -
two part question: PLEASE ANSWER BOTH PARTS.
THANKS
A: Dyl Inc's bonds currently sell for $1,180...
asked 26 minutes ago -
What are the relationships and distinctions between
the exercise of power and compliance gaining?
asked 36 minutes ago -
A student ran the following reaction in the laboratory at
283 K:
2CH2Cl2(g)
->CH4(g) +
CCl4(g) ...
asked 38 minutes ago -
Write a Prolog program to find the maximum, minimum, and range
of values in a list...
asked 43 minutes ago