Use opamp building blocks to implement the following functions:
a) Ve = Vo1 - 5*Vo2
b) Vo = 2*Ve + dVe/dt
Here, Vo1 and Vo2 are inputs, and Vo is output
Use opamp building blocks to implement the following functions: a) Ve = Vo1 - 5*Vo2 b)...
5. A waveform generator is shown below. The op amps are ideal except they limit at plus and minus 12V. The diodes are ideal (zero voltage when on) The outputs Vo1 and Vo2 as functions of time are shown on the next page 10 nF ΊΚΩ ΊΚΩ D2 01 a. What is the magnitude of Va (defined on the Vo1 waveform)? b. What is the magnitude of VB (defined on the Vos waveform)? c. What is the value of T1?...
I need help in MATLAB. I'm working on a circuits lab report and I want to plot the derivative of an input signal. The circuit is a differentiator OpAmp. It is receiving a triangle wave as an input and should output a square wave. (I've included my existing code.) The output formula is: Vout = -(Rf)*C*(dVin/dt) Where Rf is feedback resistance: Rf = 1*10^6; and C = 1*10^-6. EXISTING CODE: %% This section is copied, and then modified from another...
PART B: OPAMP as a non-inverting amplifier a) Implement the following circuit using the LM741 and energize the integrated circuit 741 with + 15v and -15v. In addition, feed the circuit with a 1 Vpp and 1KHz sinusoidal signal. Values: R2 = 10kΩ, R1 = 1KΩ b) Obtain the graph of the output voltage and the input voltage. Explain the differences between the graphs and determine the circuit gain. c) Change the R2 resistor with a 5.1k Ω resistor. Obtain...
Consider the following logic functions with a, b, c, d, e as logic inputs, x and y as intermediate outputs, and fis the output. :=e(d + x) 5 a) Implement the logic function fas a 3-stage precharged dynamic complex CMOS circuit using inverter between two consecutive stages. b) Implement the logic function fas a 3-stage precharged dynamic complex CMOS circuit using NP logic
1. Specification Write a C program to implement a simple calculator that accepts input in the following format and displays the result of the computation: calc [operand_1] [operator] [operand_2] The operands operand_1 and operand_2 are non-negative integers. The operator is one of the following: addition (+), subtraction (-), multiplication (x), division (/) and modulo (%). Note: For the multiplication operator, use letter ‘x’. If you use the asterisk ‘*’, your program will not work properly 2. Implementation • The program...
A combination circuit is specified by the following Boolean functions listed below. h(a, b, c) = b,c' + a'c Implement the circuit with a 3x8 decoder. Provide truth table and drawing the logic/circuit diagram. Use the block diagram for the decoder provided in Figure A4 in supplements. Please label the inputs and outputs clearly. Note: use single 3x8 decoder Question 2 (15 points] A priority encoder is an encoder circuit that includes the Truth Table of a priority function. The...
3. (25%) Implement the following 3 functions W,X,Y on a PLA with 4 product terms (Use common terms to optimize the design to obtain 4 or less terms) W(A, B, C) = X(A, B, C) = Y(A, B, C) = m(0, 1, 4, 5) m(3, 4, 5) m(0, 1, 2, 3)
(a) Implement the following Boolean functions using decoders. i) F1 = x'y z' + x Z ii) F2 = x y' z' + x' y (b) Implement the following Boolean function using multiplexers. i) F1 (a, b, c, d) = Σ(1, 3, 4, 11, 12, 13, 14, 15) ii) F2 (a, b, c, d)= Σ(1, 2, 5, 7, 8, 10, 11, 13, 15)
5. Use the following initial conditions for each part as follows: Assume that the forcing functions are zero prior to t=0 dt dt t, dr c. der dr2 (a) x(0)=4. x'(0)=-4; (b) x(0)=4. We were unable to transcribe this image
Implement the following Python functions. These functions take advantage of the generalized Euclid's lemma to make it possible to generate a random number within a specified range. Your implementations must be extremely efficient, and must handle very large inputs, as shown in the examples below. Implementations that perform exhaustive, exponential-time searches will receive no credit. a. Implement a function closest(t, ks) that takes two arguments: a target integer t and a list of integers ks. The function should return the...