Draw a program on the rungs below that uses a timer function. When a NO contact (I-0) is closed a coil is energized and stays energized for 10 seconds. Clearly indicate which timer function was used and what inputs and preset values were used.
In following rung we have used normally open open input instruction, which is might be connected to certain sensor or any button. This input is connected to outpit coil and timer function, which will starts immediately when input came from sensor or button.
When timer starts it will gives DONE bit after 10 seconds, which will turn off coil by normally closed contact (Interlock). This normally closed contact will get opens when DONE bit comes from timer, and turn off the coil.
Note that input is momentary.
Draw a program on the rungs below that uses a timer function. When a NO contact...
Draw a program on the rungs below that uses a timer functions to turn a coil on for 500ms and then off for 500ms in a repeating process.
All timers below start with an accumulated value of 0 and then the timer instructions are energized for 5 seconds and then de-energized for 6 seconds. For which of the timers below will the DN bits be activated at the end of the 6 second interval? (circle all that apply) 1. a TOF with time base of 0.01 and preset of 800 b.) TON with time base of 0.01 and preset of 800 TOF with time base of 1.0 and...
WILD rade on your test. must 1. The relay contact shown below is designed to operate so that a. when the relay coil is energized, there is a time delay in closing b. when the relay coil is energized, there is a time delay in opening c. when the relay coil is de energized, there is a time delay in closing d. when the relay coll is de energized, there is a time delay in opening 2. In the relay...
6. Consid shown in the discharge pump to show when they are on and off. er the ladder program shown. The graph below shows a 35 second interval of e run switch is closed at 5 seconds and opened back up at 25 seconds as graph. On the graph, add a line for the heat coil, stir motor, and RUN SWITCH T4:2 HEAT COIL STIR MOTOR Timer On Delay Timer Time Base T4:2 1.0 10 TOF Timer Off Delay Timer...
5. A milling machine has the following open-loop transfer function: (s 1)(s+3) Draw a block diagram describing a negative feedback system that includes a plant a) with transfer function of Gi(s) and a cascade proportional controller with a gain of K. b) Write the closed-loop transfer function for such a negative feedback system c The plant has poles that are solutions to P(s) 0 and zeros that are the solutions to Z(s)-0. Write an equation involving K, P(s) and Z(s)...
The graph below shows the production function for a certain firm that uses labor and capital as inputs. The function is drawn for a given level of capital. In the space underneath the graph with the function, sketch a graph of this firm’smarginal product of labor and average product of labor curves. Label them clearly. It may help you to know that marginal product equals Q0/15 when labor is 15 (or when labor is raised from 14.9 to 15.1). Note:...
how would i draw this circuit The Assignment: Create a second-timer circuit. Decade counters such as 74160 produce four bit binary codes that are BCD codes for the decimal digitals 0 to 9. The chip 7447 can be used to convert a BCD code to the corresponding decimal digit in the form of seven segment signals which can be displayed on a seven segment display unit. You can use two decade counter 74160 chips, each one connects to a 7447...
Program already solved, but I need to put function documentation headers for each and every function in your program (for the ones you write, and keep the function header I give you for the main() function). Also make sure you keep the file block header at the top of the file, and fill in the information correctly. Secondly this week you must get your indentation correct. All indentation must use 2 spaces, and you should not have embedded tabs in...
I'm having trouble understanding pointers in my c programming class. I posted the pointer assignment below. If you could leave comments pointing out where pointers are used it would be much appreciated! ----------------------------------------------------------------------------------------------------------------------------------- Write a complete C program for an automatic teller machine that dispenses money. The user should enter the amount desired (a multiple of 10 dollars) and the machine dispenses this amount using the least number of bills. The bills dispenses are 50s, 20s, and 10s. Write a...
c++ write a program that reads all values from a text file "data.txt" and stores them in ID array valuesl I. The input process from the file should be terminated when a negative value is detected. (An example of such a file is shown below). Also, the program should copy from values[ 1 any value which has even sum of digits and its index (location) to two new arrays evenArr 1 and idxArrl I, respectively. In addition, the program must...