1. Find the critical load Pcr using the bifurcation approach.
2. Investigate the stability behavior of the
asymmetric spring-bar model.
Please provide me with detailed solutions....
1. Find the critical load Pcr using the bifurcation approach. 2. Investigate the stability behavi...
Find the critical load Por of the bar-spring system shown in Fig Q1 using (i) equilibrium approach; and (2) energy approach 1. ks1 ks2 Fig. Q1 Determine the post-buckling behaviour of the perfect system for ks1/ks2L2 0.01 and ks1/ks2l2 10 and discuss its stability behaviour.
Find the critical load Por of the bar-spring system shown in Fig Q1 using (i) equilibrium approach; and (2) energy approach 1. ks1 ks2 Fig. Q1 Determine the post-buckling behaviour of the perfect system for...
Using Approach 2 please.
The basic electric circuit of a permanent-magnet DC motor and the free body diagram of the load attached to it are shown below. be The parameters of this system are identified as follows: Moment of inertia of the system, J-001 kg.m" /s2 Damping constant of the mechanical system, b-0.1N.m.s Armature and motor constants. A. K. K, 0.01 N·m/Amp Electric resistance, R-1 ohm Electric inductance, L = 0.5 H For this system, the goal is to plot...
1. Using the traditional hypothesis testing approach, calculate the critical value for testing the null hypothesis that the population mean is greater than or equal to 12, given a sample size of 49, a population standard deviation 6.06, and a significance level of 0.05. Round to two decimals. K = 2. The manager of a paint supply store wants to determine if the mean amount of paint contained in 1- gallon cans purchased from a nationally known manufacturer is actually...
Design the cooling system used to manufacture the leg of a table, shown in Fig.2. You will have to determine the required diameter D so that the leg can withstand 100 kg of axial loading. Once the diameter has been determined, you will need to determine the Revolutions per Minute (RPMs) of the fan needed to cool down the leg to 90-C in less than 2 minutes before it starts deforming after being 3D printed. Consider the leg of the...
2. SW2=1; SW1=SW3=0
Using KP=0.1, KI=4 and KD=0.3. Your program should display the
transfer functions
M1(s),M2(s),M3(s) and M4(s)
you must use matlab and include the codes.
Ks) Sw I Where .(s) is the Laplace transform of the motor's speed w (t) V(s)Is the Laplace transform ofvoltage r(t) · . K 3 and r 0.5 Find the system's step response and its three performance specifications. Hint: The system's transfer function can be rewritten as: G (s)-K sta for a = 1/τ....
MEC311 Term Test, 2019w 2. 145%) This problem is about using work-energy and impulse-momentum principles. You must answer according to the notations and coordinate systems set up for you Answers based on other coordinate sysfem or notations will not be marked. Consider a sticky ball of weight Ws 0.1 [lb] located on an incline of angle 0-30-deg. The ball is initially placed on top of a compressed linear spring of spring constant k 10 [lb/ft]; see figure. It is released...
solve quastion 3,4 and 5
B. Tasks and Guide 1. System description and Mathematical modeling The antenna positioning system is shown in Fig. 1. In this problem we consider the yaw angle control system, where 0(t) is the yaw angle. Suppose that the gain of the power amplifier is 5 , and that the gear ratio and the angle sensor (the shaft encoder and the data hold) are such that (t)= 0.40(t) where the units of v,(t) are volts and...
OPS Practice quiz 2. The benefits of risk pooling depend on the behavior of demand from one market relative to demand from another. True False 3. What is Supply Chain Management? A set of approaches utilized to efficiently integrate suppliers, manufacturers, warehouses and stores so that merchandize is produced, distributed at the right quantities, to the right locations and at the right time in order to minimize system wide costs while satisfying service level requirements. The management of the flow...
Based on the document below,
1. Describe the hypothesis Chaudhuri et al ids attempting to
evaluate; in other words, what is the goal of this paper? Why is he
writing it?
2. Does the data presented in the paper support the hypothesis
stated in the introduction? Explain.
3.According to Chaudhuri, what is the potential role of thew
alkaline phosphatase in the cleanup of industrial waste.
CHAUDHURI et al: KINETIC BEHAVIOUR OF CALF INTESTINAL ALP WITH PNPP 8.5, 9, 9.5, 10,...
Using data from the Southwest case, create a chart that plots
the relationship between each airline’s market share, in terms of
revenue or airline seat miles flown, and its profitability for two
periods: 1995-2000 and 2001-2005. Does your analysis suggest that
market share is correlated with profitability in this industry? If
you exclude Southwest Airlines and Jet Blue airlines from the
analysis (companies that use “point-to-point” route structure
rather than a “hub and spoke” route structure), how well does
market...