4-130%) A 60-Hz, 3-phase, 10-km long, fully transposed, 69-kV following conductor arrangement: 5 ...
Question: A three-phase, 60-Hz, completely transposed transmission line has a length of 100-km and has a series impedance per phase of (0.25+j0.85) ohms/mile and shunt admittance of 5.0*10^-5 Siemens/mile. The transmission line delivers 150 MW at 0.85 lagging power factor to a load connnected to its receiving end. The line-to-line voltage at the receiving end is 138-kV. Note: The Medium Length Line method should be used since it is used for distances between 50 miles to 150 miles. Determine the...
4 A three-phase, 765-kV, 50-Hz transposed line is composed of four ACSR 1,510,500, 54/19 Parrot conductors per phase with flat horizontal spacing of 16 m. The conductors have a diameter of 3.8252 cm and a GMR of 1.5453 cm. The bundle spacing is 40 cm. The line is Km long, and for the purpose of this problem, a lossless line is assumed (a) Determine the transmission line surge impedance Zc, phase constant p, wave surge impedance loading SIL, and the...
A three-phase, 50Hz, 50 km transmission line uses 3 conductor bundle conductors per phase. The diameter of each conductor in a bundle is 10 mm and the conductors are placed at the vertices of an equilateral triangle with a side length of 20 cm. The three phase bundles are horizontally placed with a distance between phase A and phase B as 1.2 m and phase B and phase C as 1m. The three phase lines are completely transposed. Calculate the...
Homework 24: Use the ALCOA conductor table from Glover, Sarma, Power System Analysis and Design, for this assignment A 12 kV 60 Hz three-phase three-wire overhead line has Drake ACSR conductors spaced 4 ft apart in an equilateral triangle. It is operating at 50 degrees C. a. Calculate resistance (0.1288 ohms/mile) of one phase of the line b. Calculate series inductance of the line (0.93 uH/m) c. Calculate shunt capacitance of the line. (12.47 pF/m) The line is 20 km...
PROBLEM: A 230-kV, 50 Hz, three-phase transmission line is 120 km long. The line has a per phase series impedance of z-0.05 +j0.45 Ω per km, and a per phase shunt admittance of y 3.4x10-6 Siemens per km. The line delivers (at the receiving end) 200 MVA, 0.8 lagging power factor at 220 kV. Now consider two cases: A- Assume that shunt parameters of the transmission line are ignored (i.e. even if this is a medium length transmission line, under...
Problem #1 Part I (50 points) Consider the following one-line diagram of a three-phase power system. Assume that the system has the following base quantities: S3 100 MVA, and VbaselL 38 kV at the generator side. The rated line-to-line terminal voltage of the generator (BUS 1) is 38 kV. A single-circuit three-phase transposed overhead line composed by one ACSR Partridge conductor per phase with vertical configuration. The transmission line length is 50 km and the distance between phases a-b, b-c...
Problem 3: A three-phase, 60 Hz transmission line is built with an ACSR conductor. The conductor diameter is 0.68 inch, GMR = 0.023 ft., and AC resistance of 0.342 /mile at 50°C. The conductors are laterally spaced with D= 1.7 m between conductor centers. The line is 50 km long and supplies a 5 MW load. The line to line load voltage is 13.2 kV. [40 points] (a) Find the total impedance of the line. (b) Determine the sending-end voltage,...
Problem 4 (10 points) A three-phase, 60 Hz, completely transposed overhead transmission line has one Redwing ACSR conductor per phase. The conductors are oriented in a flat, horizontal configuration with 5 meter spacings between A and B, 5 meter spacing between B and C, and 10 meters between A and C. What is the inductive reactance for a 10 mile length of this transmission line? Problem 5 (10 points) a.) Calculate the capacitance-to-neutral (F/m) for the transmission line of problem...
A 200-km, 230-kV, 60-Hz three-phase line has a positive-sequence series impedance ?=0.08+?0.48 Ω/km and a positive-sequence shunt admittance ?=?3.33×10−6 S/km. At full load, the line delivers 250 MW at 0.99 pf lagging and at 220 kV. Using the nominal ? circuit, calculate: a. The ABCD parameters, b. The sending-end voltage and current, c. The percent voltage regulation.
Please help me with question 2 ASAP Question 1 [15 Marks A 500-kV, 60-Hz, 3-phase completely transposed overhead line has the resistance R=0.0201/km, Ds = 0.149m and r=0.16m. The horizontal phase spacings between the conductors are 10, 10, and 20 m. Calculate a) the line inductive reactance in /km, b) the line impedance in /km, c) the line capacitance-to-neutral Can in F/m, d) the admittance-to-neutral in S/km, neglecting the effect of the earth plane, and e) the exact ABCD parameters...