For the system shown, where R(s) is the input and D(s) is the disturbance, and K and K2 are syste...
4. Consider the block diagram shown below where D(s) is a step disturbance input. D(s) Controller Plant R(s) + E(s) C(s) G2(s) Ideally you want your controller design to reject a step disturbance input at D(s). This means that in the steady state for D(s)-1, the value of Y(s) is unchanged (a) Ignoring the input R(s), what is the transfer function器in terms of Gi(s) and G2(s)? (b) For G1(s)Ks 2) and G2(s)0419 what is the steady state error resulting from...
Question 2 Consider the system shown in Figure Q2, where Wis a unit step disturbance and R is a unit step input. 0.4 s+ 1 10 Figure Q2 (5 marks) (3 marks) (c) Find the value for K so that the steady state error due to w(t) is less than 0.01; 6 marks) (d) In order to eliminate the steady state error, show whether a PI controller can be successful 6 marks) (a) Find the expression of E(s)-R(s)-Y(s) in terms...
Question 2 Consider the system shown in Figure Q2, where Wis a unit step disturbance and R is a unit step input. 0.4 s+ 1 10 Figure Q2 (5 marks) (3 marks) (c) Find the value for K so that the steady state error due to w(t) is less than 0.01; 6 marks) (d) In order to eliminate the steady state error, show whether a PI controller can be successful 6 marks) (a) Find the expression of E(s)-R(s)-Y(s) in terms...
pleas show all work thank you
Disturbance D(s) Reference Control Output Input Error Input t US) Y(s) Plant Given the above closed loop block diagram: Let aundl s) KK (a) Show that the above system will have zero steady state error for step reference input (when D(s)-0) as well as for step disturbance input (when R(s)-0). (b) LetJ B K1 and Kp0, what about the stability of the closed loop system?
Disturbance D(s) Reference Control Output Input Error Input t...
Motor Position Control with
Torque Disturbance
The following diagram models a
motor position control system with torque disturbance. The motor
transfer function from torque to position (when connected to a
voltage source) is G(s) = 1/s(0.1s + 1).
Problem 5-1: Motor Position Control with Torque Disturbance The following diagram models a motor position control system with torque disturbance. The motor transfer function from torque to position (when connected to a voltage source) is s(0.1s +1) The gain K in this...
For the feedback control system shown to the right: Find the steady state error with respect to the reference input and the disturbance for step, ramp, and parabolic inputs. Assume the inputs are 2s2 +3s+3 Equation Input Ste Ramp Parabolic H(s) = 1 r(t) = w(t) = 4t2 a. find the error to a step, ramp and parabolic input (reference input) b. find the error to a step. ramp and parabolic input (disturbance input)
HVV 10.2 Disturbance Consider the following closed loop system; K T(S) : 48 = $#18 S+14 S2+55 +6 G(s) H(s) • Determine; • T(s)= yes • E(s) = R(s)-Y(s) • Steady State error value due to step input, R(s) • Sensitivity of TF respect to K, S Solution; notes
10 Q.1 Figure Q1 shows a speed control system where Gi(s) 0.5s 1' and K(s)kp K(s) G,(s) Figure Q1: Speed Control System a) Determine the transfer function from d to y (4 marks) (b) Assuming the reference is zero, what is the steady-state error (e-r - y), in this case, you want yss since r 0) due to an unit step disturbance in d? What must the value of k be in order to make the steady-state error less than...
2. A feedback control system is subject to disturbances at the actuator input, as shown in the following block diagram. Remember that you need to use the final value theorem (and not the table) when dealing with any other input other than the reference. See the last 3 pages, 12-15, of my steady-state error lecture notes for examples on how to deal with disturbance rather than reference inputs D(s) 1 Y(s) $3+2s2+2s If the reference command is r(t) 1S 0,...
Wis) R(s u(s) 14 Gl(s) H(s) Given a system as in the diagram above, where K is an adjustable parameter pl(s) Dal(sKp+ g) Assuming W-0, find the transfer function Y(s)/R(s) h) Assuming R-0, find the transfer function Y(s)/W(s) i) What is the type of the system (with respect to steady-state error)? j) What is the steady-state error when rt)u(t) (unit-step) and w(t)-0 k) What is the s.s. error when r(t) t u(t) and w(t)-0 ) Assume r(t)-0, what is the...