Q2 A 200 mm diameter cast iron pipe with wall thickness of 15 mm is carrying water when the outle...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm wall thickness is fabricated from a 1.2 m length of spirally welded pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial forces P and P1 of 240 kN act through rigid end plates. Determine: (a) Net longitudinal and hoop stresses. (b) Normal stress acting perpendicular to weld and shear stress parallel to weld (show sketch of Mohr’s circle). (c) Determine the Factor of Safety...
A pipe with an outside diameter of 175 mm and a wall thickness of 6 mm is subjected to the loadings shown in the figure below. Р. H For this analysis, use the following values: Distances, Loads, and Moments. a = 400 mm Px = 40.5 kN Py = 68.5 kN T = 35 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,p-OkPa). (Note:...
A pipe with an outside diameter of 150 mm and a wall thickness of 5 mm is subjected to the loadings shown in the figure below. P PO a For this analysis, use the following values: Distances, Loads, and Moments. a = 450 mm Px = 11.5 kN Py = 25.5 kN T = 15 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,...
The steel pipe AB has a 106-mm outer diameter and a 6-mm wall thickness. Knowing that arm CD is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K 53 mm 6 mm 191 mm 9.2 kN 152 mm MPa MPa MPa ? max ?min
A 50-mm-diameter steel tube with a wall thickness of 2 mm just fits in a rigid hole. Find the tangential stress if an axial compressive load of 10 kN is applied. Assume υ = 0.30 and E = 200 X 10 N/m . Neglect the possibility of buckling.
A spherical tank (inside diameter 950 mm, wall thickness 6 mm) made of cast iron (k = 57 W m-1 K -1 ) is to be used to store a vapour/liquid mixture at 2 °C while it is waiting to be used in an industrial process. Calculate the percentage reduction in the rate of heat infiltration (compared to the case of no insulation) if the tank is covered in a 35 mm layer of insulation (k = 0.04 W m-1...
An alumninum (E = 68.9 GPa) cylindrical tube has an outer diameter of 200 mm, a wall thickness of 7.5 mm, and an internal pressure of 5 MPa. It is subjected to a force with the axial and transverse components shown acting at the centroid of the free end of the tube 1. Verify that the tube meets the thin-wall criterion 2. Draw the left half of the tube, and show the equivalent force-couple system acting at the centroid of...
Show complete solutions. Show FBD diagram, label properly. Show formulas and their direct substitution. 67. Find the rim thickness for a cast iron flywheel with a width of 200 mm, a mean diameter f 1.2 in a normal operating speed of 300 rpm, a coefficient fluctuation of 0.05 and which is capable of hanging 3000 N-m of kinetic energy. Assume that the hub and arms represent 10% of the rim weight and the specific weight of cast iron is 7200...
H2.3 Consider water at 20°C flowing through a horizontal pipe of diameter 15 cm and length 10 m. The flowrate is 0.021 m3/s and the wall shear stress is 5.76 N/m2. Assume fully developed flow. a. Verify that the flow is turbulent b. Determine the pressure drop [N/m2 c. Estimate the viscous sublayer thickness [mm], i.e., where y+ 5 d. Compare results of part c. with typical pipe roughness (see Table 8.1 in text and comment on implication e. Using...