Question # B.5 (a) In a communication system, suppose the associated operating temperature is dou...
Question # B.5 signal power-level at the coresponding change in is signal power-level at the input is kept constant? Is C a linear function of temperature? Justify (a) In a communication system, suppose the associated operating temperature is doubled. Then, what is the corresponding change in the system capacity (C), if the (b) A mixer-stage in a radio receiver has a NF-20 dB and this mixer-stage is preceded by a preamplifier with a NF 9 dB. The available power-gain ratio...
12 oblem # 6 The front-endof has a a radio receiver has a preamplifier followed by a mixer stage. The mixer stage with lactorN2-100 and the pre amplifier has NF, 9 dB. The overall noise factor of the 11.04. Suppose a signal of power-level equal to 5 dBm is watts,h imput of the preamplifier. Determine the output power-level of the preamplifier in Useful hint-Friis formula: SOLUTION 12 oblem # 6 The front-endof has a a radio receiver has a preamplifier...
WRITE LEGIBLY OR TYPE THE ANSWERS WITH EXPLANATIONS THANKS!!! Question # B.4 An RF system having a RF-bandwidth of 1 MHz, has a front-end preamplifier of gain (A) equal to 20 dB and a noise-figure (NF) of 4 dB. The preamplifier is followed by a mixer stage with a NF 18 dB. Suppose the signal-to-noise ratio (SNR) at the mixer output is 30 dB, find the SNR at the preamplifier input. Hint: Use Friis formula F21F (Answer hints: NF (Total)...
Noise-related problems Question # B.4 An RF system having a RF-bandwidth of 1 MHz, has a front-end preamplifier of gain (A) equal to 20 dB and a noise-figure (NF) of 4 dB. The preamplifier is followed by a mixer stage with a NF 18 dB. Suppose the signal-to-noise ratio (SNR) at the mixer output is 30 dB, find the SNR at the preamplifier input. Hint: Use Friis formula: Answer hints: NF (Total) 4.96 dB)
Problem As a communications system engineer, you are asked to setup a communication system to serve a distance of 100m using an access point transmitting signals with power 20dBm at the frequency 2.4GHz. The antennas used at the transmitter and receiver side have the gains shown in the picture below. The coaxial cables used to interface the systems to the antennas have losses shown in the picture below. What is the received signal power in dBm at the input of...
As a communications system engineer, you are asked to setup a communication system to serve a distance of 100m using an access point transmitting signals with power 20dBm at the frequency 2.4GHz. The antennas used at the transmitter and receiver side have the gains shown in the picture below. The coaxial cables used to interface the systems to the antennas have losses shown in the picture below What is the received signal power in dBm at the input of the...
Problem #2: (40 points) Consider the following communication link. Both the transmitter and receivers are properly matched to their respective antennas. Assume that the system nominal temperature is 290 K. A detailed block diagram of the receiver is shown in the figure Determine 1. The effective isotropic radiated power in dBm. 2. The space loss in dB 3. The communication link total losses in dB 4. What would be the received power at the receiver input in dBm? 5. What's...
Problem 8 Communication Link: Gain & Loss (14 points) You are given the receiver block as schematically shown below. It consists of a receiving antenna which delivers a signal to a bandpass filter. The antenna feed has a loss of -1.15 dB and the filter's loss is -2.4 dB. The filter's output drives an amplifier with gain of +40.7 dB and this RF signal is input to a mixer which performs a frequency 1translation to an IF signal (but the...
VS W l such a junction? (5 c) Suppose a (200+j75)- load is to be matched to a 300-2 transmission line to give SWR = 1. Determine the reactance of the stub and the characteristic impedance of the quarter-wave transformer, both connected directly to the load. d) (5 marks) i. For a given communication system, briefly explain the meaning of the following terms: Thermal Noise, Noise Figure, and Noise Temperature. A given communication system has a 12 GHz receiver that...
its related to RF Circuits, kindly solve all the parts as it is a one question. Question # 3: A cellular telephone receiver front-end circuit is shown below. The operating frequency is 1805-1880 MHz, and the physical temperature of the system is 300 K. A noise source with Ni = -95 dBm is applied to the receiver input. Transmission le Amplifier L=1.5B G= 12 dB T = 150K a) What is the equivalent noise temperature of the source over the...