Thanks
Figure 1: RC Circuit RL Circuit 22 kΩ Figure 2: square V in V in square 100 kHz C1 1 nF 100 mH Ta...
MENG 207-ELECTRICITY Department of Engineering & Design at Eastern Washington University Lab 6 PRE LAB 1. Print out lab handout and bring to lalb 2. Do calculations for part 1 in RC CIRCUIT section. 3. Do calculations for part 1 in RL CIRCUIT section. 4. Do calculations for part 1 in RLC CIRCUIT section OBECTVE:response Use Multisim to study the transient response of an RC and RL circuit, and the frequency response of an RLC circuit. PROCEDURES 1. Record every...
EXPERIMENT 11 STEP RESPONSE TO RC AND RL CIRCUITS pages 11-4 thru 11-7. tep response of the RC and RL circuits is included in OBJECTIVE: O analyze the voltage and current characteristics of a Resistance - Capacitance (RC) circuit when driven by a step voltage function. To analyze the voltage and current characteristics of a Resistance- Inductor (RL) circuit when driven by a step voltage function To design an RC circuit to yield a specified output voltage with a step...
R V.(t) CE + V.(0) Figure 2. The RC circuit. P1 For the RC circuit given in Figure 2 a) Obtain the transfer function Vols for Vs=Vmcosot. b) Draw the amplitude response and the phase response. c) According to the value of 0/0, as 0, 1, 2, 3, 10, 20, 100 and oo, calculate the H and 6.
The 1 mA. V, ls -VE -15 15 V, in the following differential amplifier circuit, Vcc parameters are given as β, 100, VBE# 0.7 V, pr-25 mV, K.-100 V. transistor Rc-10 kΩ For: RE-150 Ω Rc Rc REE-200 kΩ a) What is the input differential resistance, Rid b) What is the overall voltage gain vV? You c) What is input common mode resistance, d) What is the worst case common mode gain that appear across the two input terminals? (4...
2 First-Order RC Circuit: Natural Response The switch in the circuit in Figure 2 has been in position for a long time. At t = 0, the switch moves to position (the switch opens) and stays there. Assuming that V. > O for the constant voltage source, (a) find vc(0-), vc(0+), ic(0-), and ic(0+); (b) find vc(t) when t 20 (if you want, you can write vo(t) by circuit inspection; you don't need to show the differential equation); and (c)...
You can use any software of your choice Begin by connecting the waveform generator to the series combination of a 0.2uF capacitor (use a decade capacitor box) and a 1 ks resistor (use a decade resistor box). Generate a 500 Hz, 8 Vp- p square wave with a 4 Volt offset and observe this waveform on the oscilloscope's Channel 1. Monitor the voltage drop across the capacitor on Channel 2. Figure 1 shows the schematic for the RC circuit 1k...
Prelab Preparation: For the RC circuit shown in Figure 1, derive the modeling equation relating the output volta ge Vout to the input voltage vin. What is the transfer function? What is the time constant of the system? Vout Figure 1: RC Circuit What is the analytical step response solution in terms of vin, Rand C? For assumed values of R 1 K, and C 6.8 uF, perform a simulation using Matlab/Simulink assuming an input square wave signal of 5Vpp,...
Problem 1:(20 points) Consider the RL circuit in Figure 1. You may assume that the switch has been closed long enough for the voltages and currents to reach steady-state values. At timet 0 the switch is opened. 1 0 Rs Ri Figure 1: The switch in the RL circuit is opened at time t 0 1. (6 points) Find the voltage v(0-) and the current i(0) just before the switch is opened. 2. (6 points) Find the voltage v(0+) and...
Objectives: To learn transient behavior of series RC circuits To observe of time constant and its effect on charging process of capacitor using pulse waveforms Equipment: Oscilloscope Function generator Resistors (1 k) Capacitors (1 uF) Breadboard Pre-Lab Questions A pulse is a voltage or current that changes from one level to the other and back again. If a waveform's high time equals its low time, it is called a square wave. The length of each cycle (one positive peak and...
Problem 2:(20 points) Consider the RC circuit in Figure 2. You may assume that the switch has been opened long enough for the voltages and currents to reach steady-state values. At time t = 0 the switch is closed. t-0 Figure 2: The switch in the RC circuit is closed at timet0 1. (6 points) Find the voltage v(0-) and the current i(0) just before the switch is closed. 2. (6 points) Find the voltage v(0+) and the current i(0+)immediately...