Problem 8: A control system for an automatic fluid dispenser is shown below: 125 pointsl Y(s) K6s...
Consider the system shown in the following. Determine the value of k such that the damping ratio } is 0.5. Then obtain the rise time ty, peak time tp, maximum overshoot Mp, and settling time ts in the unit-step response. R(S) C(s) 16 $ + 0.8 k
Question 2 For the system shown below use the MATLAB to find: X + 0.5s+1.3 s+1.2s+1.6s For the previous system if K-1, and the input is sin(2t) find: 1) 2) 3) 4) Peak amplitude Rise time Settling time Steady state value Question 3 For the system shown below If the input is unit step find: 1) 2) 3) 4) Peak amplitude Rise time Settling time Steady state value Question 2 For the system shown below use the MATLAB to find:...
a)In the system with the block diagram shown above, calculate the parameter values a and b for a unit time (unit-step) input of ???? (peak time) value of 1 sec and ???? (settling time) value of 2 sec. b) a) Calculate the ???? (rise time) and ???? (Maximum overshoot) of the system using the parameters you find. 2 -1
For the closed-loop system shown, and given: C(s) 8.41 s+8.10 G(8 2 0.02 3.00 2out G(s) C(s) control plant Part A-Plant 1% settling time Find the 1% settling time of the plant G(s) to a unit step input. 15.38 t,3% - Submit X ncorrect; Try Again - Part B Plant: Overshoot Find the overshoot of the plant G(s)to a unit step input. Give your answer as a percentage Mp: | Value Units Submit Request Answer Part C - Closed-loop system:...
1. Consider a transfer function of a system 25 s? + 4s + 25 a) Simulation i. Using any simulation software package, plot the poles on the s-plane. ii. Using unit step input, plot the transient response when there is no additional third pole to the system. iii. Using unit step input, plot the transient response when there is an additional third pole occur at -200, -20, -10, and -2. Plot them in a single graph. Normalize all the plots...
Example 3.3.1 A control system shown in following Figure G(s)=(s+1) C(s) N(s) E(s) G,(S) R(s) S G2(s) 100 G2(s)= s(s+10) H(s) H(s) 1 1. If n(t) 0, r(t)=5+2t+10t?, make e 0.1, k-? 2. If n(t)=t, r(t)=5+2t+10t2, k=1, e=? sS I ess0.1, k=?. Question14 A control system shown in following Figure, obtain the steady-state error transfer function E(s)/N(s). N(s) E(S) GS C(S) G.(S) R(s) H(s) Question12 Obtain both analytically and computationally the rise time, peak time, maximum overshoot, and settling time...
Problem 4. Consider the control system shown below with plant G(s) that has time con- stants T1 = 2, T2 = 10, and gain k = 0.1. 4 673 +1679+1) (1.) Sketch the pole-zero plot for G(s). Is one of the poles more dominant? Using MATLAB, simulate the step response of the plant itself, along with G1(s) and G2(s) as defined by Gl(s) = and G2(s) = sti + 1 ST2+1 (2.) Design a proportional gain C(s) = K so...
Problem 2 Wis) R(s) U(s) Gol (s) D a (s) E(s) H(s) Given a system as in the diagram above, use MATLAB to solve the problems: Assume we want the closed-loop system rise time to be t, 0.18 sec S + Z H(s) 1 Gpl)s(s+)et s(s 1) s + p a) Assume W(s)-0. Draw the root locus of the system assuming compensator consists only of the adjustable gain parameter K, i.e. Dct (s) Determine the approximate range of values of...
Problem : Consider the systems A and B whose roots are shown below BI 1. Regarding stability, the systems are a) b) c) d) Both stable Both unstable A is unstable and B is stable A is stable and B is unstable 2. The responses of the systems to step input are characterized as follows: a) Both are underdamped b) Both are overdamped c) A is underdamped and B is overdamped d) A is overdamped and B is underdamped 3....
Automatic Control In unity feedback system with Gs) (s-IXs-2) With out controller, is this system stable, and why? For Gc K (proportional control) sketch the root locus. Find the range of K to make the system stable. Determine the range of K, so that the system has no overshoot Determine the range of K for steady state error to unit step input less than 20% a) b) c) d) e) In unity feedback system with Gs) (s-IXs-2) With out controller,...