Problem 1(8 points): Design a 3-bit register which has the following function table. Neatly desig...
Shift Register: Design a 4-bit shift register for the following function table. Inputs are D3D2D1D0 for parallel data load, S1S0 are the mode control, and the clock. Outputs are the register bits Q3Q2Q1Q0. Show the complete logic diagram.
Part II Design a 2-bit register to be operated according to the following function table. Show the circuit schematics and label all inputs and outputs. Si 0 0 1 1 Se Register Operation 0 No change 1 Clear the register to 0 0 Complement output 1 Load parallel data Table 1 Select Signals
Draw a logical diagram of the 4-bit register with mode selection inputs S1 and S0. The register operates in accordance with the following table of functions. S1 S0 register operation 0 0 No change 0 1 parallel load 1 0 left shift 1 1 Clear register to zero
Design a 3- bit Multipurpose Register. The register utilizes 3 "D" type flip flops with outputs Q0, Q1, Q2. The Registers has a synchronous clock input(CLK) that clocks all 3 flip flops on its positive edge The Registers has an asynchronous clear input(CLR' ) that sets all flip flops to "0" when active low. The Register has 2 select inputs, S0 and S1 that selects the functions as folows: S1 = 0, 0, 1, 1 and S0 = 0,1,0,1 and...
in VHDL Show synthesizable VHDL code for a register unit that performs operations shown below. The unit has a 3-bit mode (md) input, an asynchronous reset (rs) input, a 1-bit output control (oc) input, and an 8-bit bi-directional io bus. The internal register drives the io bus when oc is ‘I, and md is not “11 1". Use std-logic. md-000: does nothing md-001: right shift the register md-010: left shift the register md 011: up count, binary md-100: down count,...
(15 points) Your colleague is trying to code a VHDL model for a 7419 register. Review the code on the next page and make any and all correction correct working model. Note the function model. Note the function table and additional information regarding need to solve this problem. DL model for a 74194 4-bit bidirectional universal shift tions that are necessary to produce a al information regarding the problem that you Control Signals Mode CirN SI SO Outputs 1 1...
Problem 4: Design a 2 bit register whose operation is controlled by the signals C1 and C2 as follows: (Use D- Flip Flops) Y2 Y1 C 2-Bit Register Clock SD PD1 PD2 Y1 Y2+ Operation Hold C1 C2 Y2 Y1 0 10 Shift Right Y1 SD 1 0 SD Y2 Shift Left PD2 PD1 Parallel Load 1 SD: Serial Data input PD1 PD2: Parallel Data input Problem 4: Design a 2 bit register whose operation is controlled by the signals...
Problem 7. Consider the 74x194 4-bit bidirectional universal shift register shown below Determine the operation of this circuit by filling out the table. Assume that the register is cleared initially as indicated by the first row in the table, and then connected to +5V (before time t), as shown in schematic. Also assume that t 'is that time at which a positive edge occurs in the input signal 'clock'. Si and S0 inputs (given) are used to switch between modes...
Goal You'll design and build a multifunction register. The register needs to meet the following requirements: 1) The register holds a 4-bit number named Q. 2) The register has a 2-bit control input, C, that selects the function that the register will perform on the next rising clock edge 3) The register has a 4-bit data input named B. ) One of the four functions that your register needs to be able to perform is to load B into the...
Problem 3 - Arithmetie Logic Unit (ALU) Design us poins Design a 4-bit ALU that has two selection variables Si Design an optimized circuit (mus external gates for circuit B operates based on the function table given below. The arithmetic unit and So and generates the arithmetic operations given below. and generatest Use a 4-1 MUX block with Si So Cin = 1 F-A (complement) F = A+B (add) FB (transfer) F A+B F = A+ 1 (negate) F A+B+...