The load on the bracket plate consists of a service dead load of 22 kips and a service live load ...
5.14-3 Design a base plate for a W12 × 87 column supporting a service dead load of 65 kips and a service live load of 195 kips. The support will be a 16-inch × 16-inch concrete pier. Use A36 steel and = 3.5 ksi. a. Use LRFD b. Use ASD
Design a tension member and its connection for the following conditions: . Length 15 feet . The connection will be to a Vs-inch-thick gusset plate 3 All structural steel is A36 The connection will be bolted. Slip is not permitted . Service dead load 45 kips and service live load 105 kips Select a double-angle section with unequal legs, long legs back-to-back. Provide a complete sketch showing all information needed for the fab- rication of the connection. a. Use LRFD
A plate girder cross section consists of two flanges, 1 ½ inches × 15 inches, and a 5/16-inch × 66-inch web. A572 Grade 50 steel is used. The span length is 55 feet, the service live load is 2.0 kips/ft, and the dead load is 0.225 kips/ft, including the weight of the girder. Bearing stiffeners are placed at the ends, and intermediate stiffeners are placed at 6-2" and 12'-9" from each end. Does this girder have enough shear strength? a....
30 pt Select the lightest angular to support a live load LL- 50 Kips and a dead load DL30 Kips. The angular will be connected to a gusset plate through bolts. Use at least three bolts in one line and 3 in as the distance between bolts in the load direction. Use A36 The length of the angular is 28 ft. (ignore block shear) Angular wPlate 30 pt Select the lightest angular to support a live load LL- 50 Kips...
which has l A single angle tension member,Ladx3/8 kength of 7 and o'% as show bl, is made from A36 steel is connect to 3/8-in thickness ckness gust plate are 28 kips dead load and 20 kips using LRFD method and AISC )." The wrvice loads are 28 kips The servive By live load yewifivations determine the followings ) The adeyuacy of this member 2) Check Ar slenderness /s" PL which has l A single angle tension member,Ladx3/8 kength of...
Design a slip-critical bolted connection for the following conditions: • All structural steel is A36 • Length = 10 ft. • The tension member is 2L7 x 4 x 7/16 LLBB. • The connection will be to a 3/8-inch-thick gusset plate • Service dead load = 50 kips and service live load = 100 kips. Provide a complete sketch showing all information needed for the fabrication of the connection. Use LRFD.
Pleqse show details and formulas. Select a single-angle tension member of A36 steel to resist a dead load of 20 kips and a live load of 50 kips. The length of the member is 20 feet, and it will be connected to a %-inch thick gusset plate with one line of 3/4-inch- diameter bolts through the long legs. There will be four or more bolts in this Q1) line Select a single-angle tension member of A36 steel to resist a...
Problem 2: The double angle is subject to tension load, dead load T,=400 kips, live load T=200 kips, and wind load T =500 kips. The double angle is connected to a 3/8" gusset plate with four A325-X bolt with diameter of /4" in standard bolt holes as shown in the figure below. Determine whether the double angle with such a connection can resist the given load or not. The double angle is 2L4x4x1/4. One angle's gross cross-sectional area A =1.94...
A compression member is subjected to service loads of 165 kips dead load and 535 kips live load. The member is 26 feet long and pinned in each end. Use (A572 - Gr 50) steel and select a W14 shape 1) Use the equations; 2) Use the tables; 3) Use STAAD.Pro or any other commercial software to verify your design 4) Compare and comment on your results.
30 pt Select the lightest angular to support a live load LL- 50 Kips and a dead load DL30 Kips. The angular will be connected to a gusset plate through bolts. Use at least three bolts in one line and 3 in as the distance between bolts in the load direction. Use A36 The length of the angular is 28 ft. (ignore block shear) Angular wPlate