Ection A uestion 1 Hook's Law, state which variables are involtved it its calculation and explain...
Rod ABC is made of a steel for which the yield strength is oy= 450 MPa and the modulus of elasticity is E-200 GPa. Knowing that a strain energy of 11.2 J must be acquired by the rod as the axial load P is applied, determine the factor of safety of the rod with respect to permanent deformation when a -0.3 m. 18-mm diameter 12-mm diameter The factor of safety of the rod with respect to permanent deformation is
Need ASAP, Show all steps. Thanks. Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yield stress of 240 MPa. +F 200 mm Fig. Q5 (a) If a tensile axial force of 1MN is applied to the end plate, show that the maximum internal pressure that can be applied before the cylinder yields according to the Tresca criterion is 16.2...
A thin-walled pipe of 10 cm diameter is used to carry hot steam at a pressure of 2.5 MPa. The pipe is made with a steel with Young's modulus of 200 GPa, yield strength of 1000 MPa and fracture toughness (KIe) of 2.85x107 Nm32. Determine the minimum thickness of the pipe using the leak-before-break criterion assuming a semi-circular shape of the cracks in the vessel wall and a safety factor of 9. (b) 17 marks] A thin-walled pipe of 10...
(b) A thin-walled pipe of 10 cm diameter is used to carry hot steam at a pressure of 2.5 MPa. The pipe is made with a steel with Young's modulus of 200 GPa, yield strength of 1000 MPa and fracture toughness (Kic) of 2.85x10 Nm32. Determine the minimum thickness of the pipe using the leak-before-break criterion assuming a semi-circular shape of the cracks in the vessel wall and a safety factor of 9. [7 marks] (b) A thin-walled pipe of...
Question 3 A typical load case for a cylindrical pressure vessel which is on the back of a truck is estimated to include the d 1.5 m t10 mm internal pressure of p = 2 MPa torsion of and a p = 2 MPa T= 1000 kNm. The internal diameter of the pressure vessel is 1.5 m and the wall thickness is 10 mm. The vessel is made of steel with a yield stress of Sy = 400 MPa Based...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
i only need help with Q3 CEE 216 Civil Engineering Materials Steel 1. A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data collected are shown in Table 1. Create a spreadsheet to complete the following. Table 1. Load and displacement data for a 32-mm rebar sample subjected to an increasing tensile load a. Create a plot of stress-strain. Label the axes and show...
question 6 of 25 mm is pulled in tension with a 44,500 N force producing only elastic detormation . What is oreonding strain and the length between the gage marks when subjected to this force? Given: elastic modulus of copper is 105 GPa. 5. A 10-mm diameter bar of 1040 carbon steel is subjected to a tensile load of 50,000 N, taking it beyond its yield point. Calculate the elastic recov removal of the tensile load. Given: elastic modulus of...
[20 pts] A cable is made of 1040 steel which has 400 MPa yield strength and 500 MPa tensile strength. Calculate the minimum diameter required for such cable that carries a 250 kg elevator with 6 people in it without any permanent deformation to the cable. Assume a design/safety factor of 2.5. Assume the average weight of a single person as 80 kg. Gravitational acceleration: 9.81 m/s2 Lutfen birini seçin: O a. 3.38 mm O b. 3.77 mm O C....