question 6 of 25 mm is pulled in tension with a 44,500 N force producing only...
(20%) Question 6. The elastic modulus, yield strength and ultimate strength of a certain material afe 110 GPa 2400 MPa and 265 MPal respectively. If a cylindrical bar of this material 380 mm long is subjected to a uniaxial tension test and its length is increased by an amount áf O.50 mm under a tensile load ót 6660 N.At the same time its diameter decreased by0,28 mm Calculate; a) The initial diameter of the bar, (8%) d b) Under an...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
A tensile test specimen has a gage length = 50 mm and diameter = 20 mm. Yielding occurs at a load of 137900. The corresponding gage length = 51 mm, which is the 0.2 percent yield point. The maximum load of 258100 N is reached at a gage length = 62.8 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength.
Q1. A circular rod of 12 mm diameter was tested for tension. The total elongation on a 300 mm length was 0.22 mm under a tensile load of 17 KN. Find the value of E. (2.5 Marks) Answer: Q2. A prismatic bar has a cross section of 25 mm x 50 mm and a length of 2m under an axial force of 90 KN. The measured elongation of the bar is 1.5 mm. Compute the tensile stress and strain in...
1. A tensile test was performed using a standard 0.505 in. diameter specimen (Do 0.505 in) of 4140 steel with 2 inch initial gage length (Lo 2.00 in), and the following were determined: . Elastic Modulus (E)-30 x 106 psi Yield Strength (To) = 60,000 psi Strain at maximum load = 0.15 .Breaking Load (Pbreak) 15,000 lbs Maximum Load (Pa) 20,000 lbs 0 % Elongation-25% . a. (3 points) Calculate the stress at the break point: b. (5 points) Calculate...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
Suppose that you have an ASTM standard round tensile specimen of SAE4340 steel with the following gauge dimensions: gauge diameter 12.5 mm, gauge length -50 mm. You are to strairn Tensile properties of SAE4340 steel are listed in the Table Q4. Is it safe for you to use this machine for your specimen? Support your answer with detailed calculations. Table Q4. Tensile Properties of 4340 Steel Quenched and Tempered at 540°C Property Elastic Modulus (GPa) Yield Strength (MPa) Ultimate Tensile...
please help with steps to solve this problem Figure 2 [25] QUESTION 3 A pinned-pinned round bar is to be 4m long. It is subjected to a purely axial load. Determine the diameter of the bar and determine the maximum load that it can carry if the bar is made of steel with yield strength of 280 MPa and an elastic modulus of 207 GPa. The safety factor on yield should not exceed 1.5. The moment of inertia for a...
A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 MPa (55,000 psi), and an elastic modulus of 103 GPa (15.0×106 psi). A cylindrical specimen of this alloy 9.0 mm (0.35 in.) in diameter and 245 mm (9.65 in.) long is stressed in tension and found to elongate 9.0 mm (0.35 in.). A) What is the yield strain? B) What is the test strain?
Need ASAP, Show all steps. Thanks. Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...