Can someone please check my sig figs and answers? i have two different answers for the last quest...
Pre-lab EM-5 Ohm's Law and Kirchhoff's Rules Ohm's Law The resistance R of a device can be determined by either directly measuring the resistance using an ohmmeter, or by measuring the current I through it and the voltage Vacross it, and then calculating R using Ohm's Law V R= (1) If the voltage across a resistor is 10V, and the current passing through it is 2.5 mA. of the resistor? What is the resistance R= Ω. Kirchhoffs Loop Rule Around...
A circuit is constructed with five resistors and one real battery as shown above right. We model. The real battery as an ideal emf V = 12 V in series with an internal resistance r as shown above left. The values for the resistors are: R = R3 = 40 N, R4 = Rs = 80 and R2 = 142 N. The measured voltage across the terminals of the batery is Vbattery = 11.41 V. I R R R R4...
Need help with conclusion questions please 1. The objectives of this lab are (1) to determine the actual (A) total resistance of three resistors connected in series and compare it with the experimental (E ) value of total resistance (2) to determine the actual (A) total resistance of three resistors connected in parallel and compare it with the experimental(E ) value of total resistance II. Apparatus(Equipment): Voltage source, ammeter that measures current , voltmeter that measures voltage. II. Procedure: Three...
I am working on my Physics lab report where it was all about Direct Current Measurement and Ohm’s Law. We had 5 different resistors and had to construct different circuits using a power supply, volt-ohm-milliammeter (VOM) and a digital multimeter to get measurements of resistance, voltage, and current. Nominal values of resistance and tolerance Resistor Nominal Resistance (Ohms) Tolerance (Ohms) R1 680 +/- 68 R2 1000 +/- 50 R3 1500 +/- 75 R4 4700 +/- 470 R5 10,000 +/- 500...
Pease answer questions 4 and 5! Thank you so much! 4. Connect the 2nd resistor in parallel with the 1st resistor and connect that combination to the battery. Measure the following: The current passing through the R1, I1 = ___0.0058____ A The current passing through the R2, I2 = ___0.0031____ A The current supplied by the battery, I = ___0.0092____ A Calculate I1 + I2 = ____________ A Is the following statement true? I = I1 +...
please answer all questions A proton and an electron enter a uniform magnetic field. The velocity vector of each particle is perpendicular to the magnetic field. If their circular orbits have the same radii, what is the ratio of their speeds (Velectron/ proton)? O 5.5E-4 O 0.5 O 1.0 04.0 1800 A horizontal length of current-carrying wire is suspended from two identical flexible leads that are under tension due to the weight of the wire. The wire is oriented at...
ANSWER ALL PLEASE Question 20 2 pts In the Figure below, V1 = 14 V, V2 = 8 V, V3 = 10 V, R1 = 2.00, R2 = 4.0, and R3 = 2.00 Find the electric currents is, iz, and is. (Hint: use the junction a and the two loops). RI R 14 M4 Equations: Kirchoff's Junction (node) rule: 11 = 12 + iz Kirchoff's Loop rule (left loop): V1 - iRi - iz R2 + V2 = 0 Kirchoffs...
Answer 4 & 5 please! thank you! R values = Resistor value, R1 = 990 Ohms Resistor value, R2 = 2050 Ohms 4. Connect the 2nd resistor in parallel with the 1st resistor and connect that combination to the battery. Measure the following: The current passing through the R1, I1 = ___0.0058____ A The current passing through the R2, I2 = ___0.0031____ A The current supplied by the battery, I = ___0.0092____ A Calculate I1 + I2 =...
CAN SOMEONE FILL OUT THIS TABLE PLEASE?? I HAVE TRIED MULTIPLE TIME AND I AM NOT GETTING ANYTHING RIGHT. THANK YOU :)))) 2uF 10HZ 1k PREPARATION In an AC circuit capacitors and inductors have an effective resistance that restricts the flow of current, this is known as impedance. An equivalent to Ohm's law can be written where resistance R is replaced by the impedance Z: V = 12 (9-4) where V and I are either the root mean squares or...
im currently doing an assignment where i must design a two stage bipolar transistor, i just need the calculations and values for each component and then i can run simulated experiments and complete my work here is the schematic the transistor used is the BC846B the supply voltage is 15 v the collector currents 1 (ICq1) = 1.5mA the collector current 2 (ICq2) = 7.5 mA output voltage swing= max frequency response = 50- 20 khz i must calculate the...