Problems in this question refer to the following sequence of instructions: I1 w $%16, -100 ($6) I2: 1w $4, 8 ($16) I3: add $5, $4, $4 Also, assume the following cycle times for each of the optio...
Question 1: Problems in this exercise refer to the following sequence of instructions : LW $5, -16($5) SW $5, -16($5) ADD $5, $5, $5 A) Indicate dependences and their type. (40 Points) B) Assume there is not forwarding in this pipeline processor, indicate hazards and add NOP instructions to eliminate them. C) Assume there is full forwarding, indicate hazards and add NOP instructions to eliminate unresolved cases. The remaining problem in this exercise assumes the following clock cycle times: Without...
In this exercise, we examine how data dependences affect execution in the basic 5-stage pipeline described in Section 4.5. Problems in this exercise refer to th following sequence of instructions: addi $2,$2,22 SW $3,20($2) OR $4,$2,$3 Also, assume the following cycle times for each of the options related to forwarding: Without Forwarding With Full Forwarding 300ps With ALU-ALU Forwarding Only 250ps 290ps 4.9.1 [10] <4.5> Indicate dependences and their type. 4.9.2 [10] <S4.5> Assume there is no forwarding in this...
Computer architecture help:
(60 points) The following instructions are executed on the 5-stage MIPS pipelined datapath. add r5,r2, r1 lw r3, 4(r5) lw r2, 0(r2) or r3, r5, r3 sw r3, 0(r5) (a) (20 points) List the data hazards in the above code. For each data hazard identified, clearly mark the source and the destination. For example you can say, there is a data hazard from instruction X to instruction Y on register Z. (b) (20 points) Assume there is...
Ch04.2. [3 points] Consider the following assembly language code: I0: ADD R4 R1RO I1: SUB R9R3 R4; I2: ADD R4 - R5+R6 I3: LDW R2MEMIR3100]; 14: LDW R2 = MEM [R2 + 0]; 15: STW MEM [R4 + 100] = R3 ; I6: AND R2R2 & R1; 17: BEQ R9R1, Target; I8: AND R9 R9&R1 Consider a pipeline with forwarding, hazard detection, and 1 delay slot for branches. The pipeline is the typical 5-stage IF, ID, EX, MEM, WB MIPS...
Given the following sequence of instructions to be executed on a 5-stage pipelined datapath as decrypted in our textbook: I1: add $8, $12,$10 12: SW $9,0 ($8) 13: lw $8,4($9) I4: and $12,$12,$8 15: SW $8,0($9) a. List true dependencies in the given sequence in the format of (register involved producer instruction, consumer instruction). Use labels to indicate instructions For example: ($0, I10, I11) means a true dependence between instruction I10 and I11: value of register $0 is generated by...
1. Given the following instruction sequence for the MIPS processor with the standard 5 stage pipeline $10, S0. 4 addi lw S2.0(S10) add sw S2,4(510) $2, $2, $2 Show the data dependences between the instructions above by drawing arrows between dependent instructions (only show true/data dependencies). a. Assuming forwarding support, in what cycle would the store instruction write back to memory? Show the cycle by cycle execution of the instructions as they execute in the pipeline. Also, show any stalls...
Given the following sequence of instructions: lw $s2, 0($s1) //1 lw $s1, 40($s3) //2 sub $s3, $s1, $s2 //3 add $s3, $s2, $s2 //4 or $s4, $s3, $zero //5 sw $s3, 50($s1) //6 a. List the read after write (current instruction is reading certain registers which haven’t been written back yet) data dependencies. As an example , 3 on 1 ($s2) shows instruction 3 has data dependency on instruction 1 since it is reading register $s2. b. Assume the 5...