Find the maximum design axial load strength for the tied column of cross section shown in Figure 1.1. Check the ties. Assume a short column. Use f’c = 4000 psi and fy = 60,000 psi for both longitudinal steel and ties. Also, draw the flexural and shear reinforcement on a sketch.
AA All are calculated as per ACI-318
Find the maximum design axial load strength for the tied column of cross section shown in Figure 1.1. Check the ties. Assume a short column. Use f’c = 4000 psi and fy = 60,000 psi for both longitudina...
Design a square tied column to carry axial service loads of 320 kips dead load and 190 kips live load. There is no identified applied moment. Assume that the column is short. Use f’c =4000 psi and fy = 60,000 psi. Also, draw the flexural and shear reinforcement on a sketch. Case 3: Design of Short Columns - Small Eccentricity Design a square tied column to carry axial service loads of 320 kips dead load and 190 kips live load....
Show Diagrams Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1 is adequate to carry a factored axial load Pu of 540 kips. Assume small eccentricity. Check the spiral. Use fc 4000 psi and fy -60,000 psi. 큠.φ @ 2 7-'8 bars 1cover Figure 2.1 Spiral Column Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1...
Solve please. CMCE 2416 Elements of Structural Design - Concrete Assignment 4: Short Column with Axial Load Determine if a 10" x 10" tied column reinforced with 4 #5 longitudinal bars is adequate to carry an axial load of Pu = 118 kips. Design the ties. Concrete compressive strength is 4,000 psi and the yield strength of both the longitudinal bars and the ties fy = 60,000 psi.
Design a square tied column to support an axial dead load of PD-260 k, P-450 k Include the design of ties or spirals and a sketch of the cross sections selected, including bar arrangements fc = 4000 psi, and fy = 60,000 psi. Initially assume Ps= 4%.
Problem 4 (30 points) Design a short square tied column to carry an axial dead load of 150 kips and a live load of 400 kips. Assume that the applied moments on the column are negligible. Use fc = 4,000 psi and fy = 60,000 psi. Assume a steel ratio of 3% (pg = 0.03).
Design a short square tied column to carry a factored axial load of 1300k and a factored moment of 550kft. Place the reinforcement uniformly around the column. Design the ties. Assume interior exposure, f’c = 4000psi, fy = 60,000psi
a. The beam of the cross section shown has f'c = 3000 psi and fy = 60,000 psi. Calculate Mn. b. Same cross section as part (a) but the steel is changed to four No. 10 bars. Calculate Mn. Calculate the percent increase in Mn and As. c. Same cross section as part (a) but the depth d is increased to 28 in. Calculate Mn. Calculate the percent increase in Mn and d. d. Same cross section as part (a)...
1) [Design] A reinforced concrete column is to be sized to carry pure axial compressive load. According to ACI 318, what is the smallest possible cross-sectional area (Ag) that the column can use in design supporting an axial dead load of 200 kips (unfactored) and live load of 400 kips (unfactored). Use fc = 4,000 psi and fy = 60 ksi. Assume pe = 0.08 and ties for transverse reinforcement. Be sure to include the appropriate design factors and use...
Problem 4 Load and Load Combinations (50pts) With fy 60,000 psi and fc' 4000 psi, select the tensile reinforcing for the edge L beam AB for the floor system shown in Figure 4.1. The cross section of the floor system is shown in Figure 4.2. Note that LI = 6ft and L2 = 12ft. Assume simple supports at sides A and B. The live load is to be 80 psf, while the dead load in addition to the concrete's weight...
Ql: design short tied column to carry dead load 1600 kN and live load 1400 kN. 28 N/mm and Ty -420 N/mm Q2: design circular column spirally reinforced subjected to the following loads P 1000 kN Use fc-28 N/mnn, and fy =420 N/m rm2 Q 3: The 300 x 500 mm column shown in Fig. Q3 is reinforced with 8 No. 29 bars arranged around the column perimeter, providing an area Ast 5160 mm2. A factored load Pu of 1...