Design a short square tied column to carry a factored axial load of 1300k and a...
Design a short square tied column to carry a factored axial load of 1300k and a factored moment of 550kft. Place the reinforcement uniformly around the column. Design the ties. Assume interior exposure, f’c = 4000psi, fy = 60,000psi
Homework Answers
Add Answer to:
Design a short square tied column to carry a factored
axial load of 1300k and a...
Design a square tied column to carry axial service loads of 320 kips dead load and 190 kips live load. There is no identified applied moment. Assume that the column is short. Use f’c =4000 psi and fy...
Design a square tied column to carry axial service loads of 320
kips dead load and 190 kips live load. There is no identified
applied moment. Assume that the column is short. Use f’c =4000 psi
and fy = 60,000 psi. Also, draw the flexural and shear
reinforcement on a sketch.
Case 3: Design of Short Columns - Small Eccentricity Design a square tied column to carry axial service loads of 320 kips dead load and 190 kips live load....
Design a spiral column to carry a factored axial load of 375 ksi. Use f’c =...
Design a spiral column to carry a factored axial load of 375 ksi. Use f’c = 3 ksi and fy = 40 ksi. Use a reinforcement ratio p = 0.02
Find the maximum design axial load strength for the tied column of cross section shown in Figure 1.1. Check the ties. Assume a short column. Use f’c = 4000 psi and fy = 60,000 psi for both longitudina...
Find the maximum design axial load strength for the tied column
of cross section shown in Figure 1.1. Check the ties. Assume a
short column. Use f’c = 4000 psi and fy = 60,000 psi for both
longitudinal steel and ties. Also, draw the flexural and shear
reinforcement on a sketch.
Case 1: Design of Short Columns- Small Eccentricity Find the maximum design axial load strength for the tied column of cross section shown in Figure 1.1. Check the ties....
Problem 4 (30 points) Design a short square tied column to carry an axial dead load...
Problem 4 (30 points) Design a short square tied column to carry an axial dead load of 150 kips and a live load of 400 kips. Assume that the applied moments on the column are negligible. Use fc = 4,000 psi and fy = 60,000 psi. Assume a steel ratio of 3% (pg = 0.03).
1) [Design] A reinforced concrete column is to be sized to carry pure axial compressive load....
1) [Design] A reinforced concrete column is to be sized to carry pure axial compressive load. According to ACI 318, what is the smallest possible cross-sectional area (Ag) that the column can use in design supporting an axial dead load of 200 kips (unfactored) and live load of 400 kips (unfactored). Use fc = 4,000 psi and fy = 60 ksi. Assume pe = 0.08 and ties for transverse reinforcement. Be sure to include the appropriate design factors and use...
Design a square tied column to support an axial dead load of PD-260 k, P-450 k...
Design a square tied column to support an axial dead load of PD-260 k, P-450 k Include the design of ties or spirals and a sketch of the cross sections selected, including bar arrangements fc = 4000 psi, and fy = 60,000 psi. Initially assume Ps= 4%.
8. Find the necessary reinforcement for a square column (16 in x 16 in) to carry...
8. Find the necessary reinforcement for a square column (16 in x 16 in) to carry a factored load Pu = 265 kips and a factored moment M, of 320 ft-kip. Assume #4 ties, f'c = 4000 psi and fy = 60,000 psi. Include the spacing of the ties assuming that the acting shear is negligible (<<V/2).
Show Diagrams Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1 is adequate to carry a factored axial load Pu of 540 kips. A...
Show Diagrams
Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1 is adequate to carry a factored axial load Pu of 540 kips. Assume small eccentricity. Check the spiral. Use fc 4000 psi and fy -60,000 psi. 큠.φ @ 2 7-'8 bars 1cover Figure 2.1 Spiral Column
Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1...
Solve please. CMCE 2416 Elements of Structural Design - Concrete Assignment 4: Short Column with Axial...
Solve please.
CMCE 2416 Elements of Structural Design - Concrete Assignment 4: Short Column with Axial Load Determine if a 10" x 10" tied column reinforced with 4 #5 longitudinal bars is adequate to carry an axial load of Pu = 118 kips. Design the ties. Concrete compressive strength is 4,000 psi and the yield strength of both the longitudinal bars and the ties fy = 60,000 psi.
Design a square footing to support an 18 in. square column tied interior column reinforced with...
Design a square footing to support an 18 in. square column tied interior column reinforced with 8 #9 bars. The column carries an unfactored axial dead load of 245 kips and an axial live load of 200 kips. The base of the footing is 4.0ft. below final grade and allowable soil pressure is 5 k/ft2 Use ??′ = 3.0 ksi and fy = 60.0 ksi
Design a square tied column to carry axial service loads of 320
kips dead load and 190 kips live load. There is no identified
applied moment. Assume that the column is short. Use f’c =4000 psi
and fy = 60,000 psi. Also, draw the flexural and shear
reinforcement on a sketch.
Case 3: Design of Short Columns - Small Eccentricity Design a square tied column to carry axial service loads of 320 kips dead load and 190 kips live load....
Find the maximum design axial load strength for the tied column
of cross section shown in Figure 1.1. Check the ties. Assume a
short column. Use f’c = 4000 psi and fy = 60,000 psi for both
longitudinal steel and ties. Also, draw the flexural and shear
reinforcement on a sketch.
Case 1: Design of Short Columns- Small Eccentricity Find the maximum design axial load strength for the tied column of cross section shown in Figure 1.1. Check the ties....
Problem 4 (30 points) Design a short square tied column to carry an axial dead load of 150 kips and a live load of 400 kips. Assume that the applied moments on the column are negligible. Use fc = 4,000 psi and fy = 60,000 psi. Assume a steel ratio of 3% (pg = 0.03).
1) [Design] A reinforced concrete column is to be sized to carry pure axial compressive load. According to ACI 318, what is the smallest possible cross-sectional area (Ag) that the column can use in design supporting an axial dead load of 200 kips (unfactored) and live load of 400 kips (unfactored). Use fc = 4,000 psi and fy = 60 ksi. Assume pe = 0.08 and ties for transverse reinforcement. Be sure to include the appropriate design factors and use...
Design a square tied column to support an axial dead load of PD-260 k, P-450 k Include the design of ties or spirals and a sketch of the cross sections selected, including bar arrangements fc = 4000 psi, and fy = 60,000 psi. Initially assume Ps= 4%.
8. Find the necessary reinforcement for a square column (16 in x 16 in) to carry a factored load Pu = 265 kips and a factored moment M, of 320 ft-kip. Assume #4 ties, f'c = 4000 psi and fy = 60,000 psi. Include the spacing of the ties assuming that the acting shear is negligible (<<V/2).
Show Diagrams
Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1 is adequate to carry a factored axial load Pu of 540 kips. Assume small eccentricity. Check the spiral. Use fc 4000 psi and fy -60,000 psi. 큠.φ @ 2 7-'8 bars 1cover Figure 2.1 Spiral Column
Case 2: Design of Short Columns - Small Eccentricity Determine whether the spiral column of cross section shown in Figure 2.1...
Solve please.
CMCE 2416 Elements of Structural Design - Concrete Assignment 4: Short Column with Axial Load Determine if a 10" x 10" tied column reinforced with 4 #5 longitudinal bars is adequate to carry an axial load of Pu = 118 kips. Design the ties. Concrete compressive strength is 4,000 psi and the yield strength of both the longitudinal bars and the ties fy = 60,000 psi.
Most questions answered within 3 hours.
-
The blues made its way into many kinds of music. Eric Clapton,
The Beatles, and Elvis...
asked 21 minutes ago -
If you’re standing at the bottom of a hill and asked to evaluate
it while being...
asked 1 hour ago -
1. Which region has taken the lead in the world of
e-waste handling?
a) European Union...
asked 1 hour ago -
A 8.15- g bullet from a 9-mm pistol has a velocity of 366.0 m/s.
It strikes...
asked 2 hours ago -
The outstanding bonds of Alpha Extracts have a yield to maturity
of 7.4 percent and a...
asked 2 hours ago -
The Problem: The Case of the Harmonizing Vacations
Your CEO is exploring partnering with a European...
asked 4 hours ago -
A chemical equation is balanced by adding coefficients in front
of some formulas so that the...
asked 4 hours ago -
From the literature (reference your sources): What are the
lattice parameters of calcite and aragonite? Why...
asked 4 hours ago -
Your system is rejecting the question am asking which is
preceded by a case study. It...
asked 4 hours ago -
3. On January 2, 2000, Larry creates a trust with himself as
trustee. Larry as trustee...
asked 4 hours ago -
A member of the volleyball team spikes the ball. During this
process, she changes the velocity...
asked 4 hours ago -
Are adult gamers less likely to use a gaming console (Xbox,
PlayStation, Wii, etc...) than teen...
asked 5 hours ago